- 您現在的位置：買賣IC網 > Datasheet目錄42 > LTC4225IGN-1#PBF (Linear Technology)IC CONTROLLER HOT SWAP 24-SSOP Datasheet資料下載
參數資料
| 型號： | LTC4225IGN-1#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 13/24頁 |
| 文件大?。?/td> | 346K |
| 描述： | IC CONTROLLER HOT SWAP 24-SSOP |
| 標準包裝： | 55 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電流限制： | 可調 |
| 電源電壓： | 2.9 V ~ 18 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 24-SSOP |
| 包裝： | 管件 |
LTC4225-1/LTC4225-2
13
422512f
Active Current Loop Stability
The active current loop on the HGATE pin is compensated
by the parasitic gate capacitance of the external N-channel
MOSFET . No further compensation components are nor-
mally required. In the case when a MOSFET with C
ISS
d
2nF is chosen, an R
HG
and C
HG
compensation network
connected at the HGATE pin may be required. The value
of C
HG
is selected based on the inrush current allowed for
the output load capacitance. The resistor, R
HG
, connected
in series with C
HG
accelerates the MOSFET gate recovery
for active current limiting after a fast gate pull-down due
to an output short. The value of C
HG
should be d100nF
and R
HG
should be between 10?and 100?for optimum
performance.
TMR Pin Functions
An external capacitor, C
T
, connected from the TMR pin to
GND serves as fault filtering when the supply output is in
active current limit. When the voltage across the sense
resistor exceeds the circuit breaker trip threshold (50mV),
TMR pulls up with 100礎. Otherwise, it pulls down with 2礎.
The fault filter times out when the 1.235V TMR threshold
is exceeded, causing the corresponding FAULT pin to pull
low. The fault filter delay or circuit breaker time delay is:
t
CB
= C
T
" 12[ms/礔]
After the circuit breaker timeout, the TMR pin capacitor
pulls down with 2礎 from the 1.235V TMR threshold
until it reaches 0.2V . Then, it completes 14 cooling cycles
consisting of the TMR pin capacitor charging to 1.235V
with a 100礎 current and discharging to 0.2V with a 2礎
current. At that point, the HGATE pin voltage is allowed to
start up if the fault has been cleared as described in the
Resetting Faults section. When the latched fault is cleared
during the cool-off period, the corresponding FAULT pin
pulls high. The total cool-off time for the MOSFET after
an overcurrent fault is:
t
COOL
= C
T
" 11[s/礔]
If the latched fault is not cleared after the cool-off period,
the cooling cycles continue until the fault is cleared.
After the cool-off period, the HGATE pin is only allowed to
pull up if the fault has been cleared for the latch-off part
(LTC4225-1). For the auto-retry part (LTC4225-2), the
latched fault is cleared automatically following the cool-off
period and the HGATE pin voltage is allowed to restart.
Resetting Faults (LTC4225-1)
For the latch-off part (LTC4225-1), an overcurrent fault
is latched after tripping the circuit breaker, and the cor-
responding FAULT pin is asserted low. If the LTC4225
controls the MOSFETs on two supplies, only the Hot Swap
MOSFET on the supply at fault is turned off and the other
is not affected.
To reset a latched fault and restart the output, pull the
corresponding ON pin below 0.6V for more than 100祍
and then high above 1.235V . The fault latches reset and
the FAULT pin deasserts on the falling edge of the ON pin.
When ON goes high again, a 100ms debounce cycle is
initiated before the HGATE pin voltage restarts. Toggling
the EN pin high and then low again also resets a fault,
but the FAULT pin pulls high at the end of the 100ms
debounce cycle before the HGATE pin voltage starts up.
Bringing all the supplies below the INTV
CC
undervoltage
lockout threshold (2.2V) shuts off all the MOSFETs and
resets all the fault latches. A 100ms debounce cycle is
initiated before a normal start-up when any of the supplies
is restored above the INTV
CC
UVLO threshold.
Auto-Retry after a Fault (LTC4225-2)
For the auto-retry part (LTC4225-2), the latched fault is reset
automatically after a cool-off timing cycle as described in
the TMR Pin Functions section. At the end of the cool-off
period, the fault latch is cleared and FAULT pulls high. The
HGATE pin voltage is allowed to start up and turn on the
Hot Swap MOSFET . If the output short persists, the supply
powers up into a short with active current limiting until
the circuit breaker times out and FAULT again pulls low. A
new cool-off cycle begins with TMR ramping down with
a 2礎 current. The whole process repeats itself until the
output short is removed. Since t
CB
and t
COOL
are a func-
tion of TMR capacitance, C
T
, the auto-retry duty cycle is
equal to 0.1%, irrespective of C
T
.
Figure 6 shows an auto-retry sequence after an overcurrent
fault.
applicaTions inForMaTion
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4230CGN#TRPBF | IC CONTRLLR HOT SWAP TRPL 20SSOP |
| LTC4232CDHC#TRPBF | IC CTLR HOT SWAP 5A 16-DFN |
| LTC4240IGN#TRPBF | IC CTRLR HOTSWAP CPCI I2C 28SSOP |
| LTC4241IGN#PBF | IC CTRLR HOTSWAP 3.3V AUX 20SSOP |
| LTC4242CUHF#TRPBF | IC CNTRLR HOT SWAP 38-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4225IGN-2#PBF | 功能描述:IC CONTROLLER HOT SWAP 24-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4225IGN-2#TRPBF | 功能描述:IC CTLR HOT SWAP DUAL 24-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4225IUFD-1#PBF | 功能描述:IC CONTROLLER HOT SWAP 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4225IUFD-1#TRPBF | 功能描述:IC CTLR HOT SWAP DUAL 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4225IUFD-2#PBF | 功能描述:IC CONTROLLER HOT SWAP 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。