- 您現在的位置：買賣IC網 > PDF目錄44996 > LTC4097EDDB (LINEAR TECHNOLOGY CORP) 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO12 PDF資料下載
參數資料
| 型號： | LTC4097EDDB |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO12 |
| 封裝： | 3 X 2 MM, 0.75 MM HEIGHT, PLASTIC, DFN-12 |
| 文件頁數： | 7/20頁 |
| 文件大?。?/td> | 219K |
| 代理商： | LTC4097EDDB |
LTC4097
15
4097f
APPLICATIONS INFORMATION
LTC4097
DCIN
USBIN
IUSB
IDC
BAT
HPWR
ITERM
RISET
2k
1%
RITERM
2k
1%
WALL
ADAPTER
USB
PORT
1
F
1
F
+
100mA
(USB, HPWR = LOW)
500mA
4097 F02
GND
4.2V
1-CELL
Li-Ion
BATTERY
LTC4097
DCIN
USBIN
IUSB
IDC
BAT
VNTC
HPWR
NTC
CHRG
ITERM
RIDC
1.24k
1%
WALL
ADAPTER
USB
PORT
1
F
1
F
+
800mA (WALL)
100mA/500mA (USB)
4097 F03
GND
RIUSB
2k
1%
RNTC
100k
RNTCBIAS
100k
1k
4.2V
1-CELL
Li-Ion
BATTERY
RITERM
2k
1%
Figure 2. Dual Input Charger Circuit. The
Wall Adapter Charge Current and USB Charge
Current are Both Programmed to be 500mA
Figure 3. Full Featured Dual Input Charger Circuit
Using a Single Charge Current Program Resistor
In applications where the programmed wall adapter charge
current and USB charge current are the same, a single
program resistor can be used to set both charge currents.
Figure 2 shows a charger circuit that uses one charge cur-
rent program resistor. In this circuit, one resistor programs
the same charge current for each input supply.
II
V
R
CHRG DC
CHRG USB
SET
()
(
)
==
1000
The LTC4097 can also program the wall adapter charge
current and USB charge current independently using two
program resistors, RIDC and RIUSB. Figure 3 shows a
charger circuit that sets the wall adapter charge current
to 800mA and the USB charge current to 500mA.
Stability Considerations
The constant-voltage mode feedback loop is stable without
any compensation provided a battery is connected to the
charger output. However, a 4.7F capacitor with a 1Ω series
resistor is recommended at the BAT pin to keep the ripple
voltage low when the battery is disconnected. When the
charger is in constant-current mode, the charge current
program pin (IDC or IUSB) is in the feedback loop, not the
battery. The constant-current mode stability is affected by
the impedance at the charge current program pin. With no
additional capacitance on this pin, the charger is stable
with program resistor values as high as 20KΩ (ICHRG =
50mA); however, additional capacitance on these nodes
reduces the maximum allowed program resistor.
Power Dissipation
When designing the battery charger circuit, it is not neces-
sary to design for worst-case power dissipation scenarios
because the LTC4097 automatically reduces the charge
current during high power conditions. The conditions
that cause the LTC4097 to reduce charge current through
thermal feedback can be approximated by considering the
power dissipated in the IC. Most of the power dissipation
is generated from the internal MOSFET pass device. Thus,
the power dissipation is calculated to be:
PD = (VCC – VBAT) IBAT
PD is the power dissipated, VCC is the input supply volt-
age (either DCIN or USBIN), VBAT is the battery voltage
and IBAT is the charge current. The approximate ambient
temperature at which the thermal feedback begins to
protect the IC is:
TA = 115°C – PD θJA
TA = 115°C – (VCC – VBAT) IBAT θJA
Example: An LTC4097 operating from a 5V USB adapter
(on the USBIN input) is programmed to supply 500mA
full-scale current to a discharged Li-Ion battery with a
voltage of 3.3V. Assuming θJA is 60°C/W (see Thermal
Considerations), the ambient temperature at which the
LTC4097 will begin to reduce the charge current is ap-
proximately:
TA = 115°C – (5V – 3.3V) (500mA) 60°C/W
TA = 115°C – 0.85W 60°C/W = 115°C – 51°C
TA = 64°C
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4098EUDC-1#TRPBF | BATTERY CHARGE CONTROLLER, 2650 kHz SWITCHING FREQ-MAX, PQCC20 |
| LTC4098EPDC-1#PBF | BATTERY CHARGE CONTROLLER, 2650 kHz SWITCHING FREQ-MAX, PQCC20 |
| LTC4098EUDC-1#PBF | BATTERY CHARGE CONTROLLER, 2650 kHz SWITCHING FREQ-MAX, PQCC20 |
| LTC4110EUHF#TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC38 |
| LTC4110EUHF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC38 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4097EDDB#PBF | 制造商:Linear Technology 功能描述:Battery Charger Li-Ion/Li-Pol 1200mA 4.2V 12-Pin DFN EP |
| LTC4097EDDB#TRMPBF | 功能描述:IC CHARGER LI-ION/POLY 12-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| LTC4097EDDB#TRPBF | 功能描述:IC CHARGER LI-ION/POLY 12-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC4098 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual-Input Power Manager |
| LTC4098-1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual-Input Power Manager |
發布緊急采購，3分鐘左右您將得到回復。