- 您現在的位置：買賣IC網 > PDF目錄98003 > LTC4085EDE-3#TRPBF (LINEAR TECHNOLOGY CORP) POWER SUPPLY MANAGEMENT CKT, PDSO14 PDF資料下載
參數資料
| 型號： | LTC4085EDE-3#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | POWER SUPPLY MANAGEMENT CKT, PDSO14 |
| 封裝： | 4 X 3 MM, PLASTIC, MO-229, DFN-14 |
| 文件頁數： | 8/24頁 |
| 文件大?。?/td> | 275K |
| 代理商： | LTC4085EDE-3#TRPBF |
LTC4085-3
16
40853f
Battery Charger
The battery charger circuits of the LTC4085-3 are designed
for charging single cell lithium-ion batteries. Featuring
an internal P-channel power MOSFET, the charger uses a
constant-current/constant-voltage charge algorithm with
programmable current and a programmable timer for
charge termination. Charge current can be programmed
up to 1.5A. The nal oat voltage accuracy is ±0.8% typi-
cal. No blocking diode or sense resistor is required when
powering the IN pin. The CHRG open-drain status output
provides information regarding the charging status of the
LTC4085-3 at all times. An NTC input provides the option
of charge qualication using battery temperature.
An internal thermal limit reduces the programmed charge
current if the die temperature attempts to rise above a
preset value of approximately 105°C. This feature protects
the LTC4085-3 from excessive temperature, and allows
the user to push the limits of the power handling capabil-
ity of a given circuit board without risk of damaging the
LTC4085-3. Another benet of the LTC4085-3 thermal limit
is that charge current can be set according to typical, not
worst-case, ambient temperatures for a given application
with the assurance that the charger will automatically
reduce the current in worst-case conditions.
The charge cycle begins when the voltage at the OUT pin
rises above the output UVLO level and the battery voltage
is below the recharge threshold. No charge current actually
ows until the OUT voltage is greater than the output UVLO
level and 100mV above the BAT voltage. At the beginning
of the charge cycle, if the battery voltage is below 2.8V,
the charger goes into trickle charge mode to bring the
cell voltage up to a safe level for charging. The charger
goes into the fast charge constant-current mode once
the voltage on the BAT pin rises above 2.8V. In constant-
current mode, the charge current is set by RPROG. When
the battery approaches the nal oat voltage, the charge
current begins to decrease as the LTC4085-3 switches to
constant-voltage mode. When the charge current drops
below 10% of the programmed charge current while in
constant-voltage mode the CHRG pin assumes a high
impedance state.
An external capacitor on the TIMER pin sets the total
minimum charge time. When this time elapses the
charge cycle terminates and the CHRG pin assumes a
high impedance state, if it has not already done so. While
charging in constant-current mode, if the charge current
is decreased by thermal regulation or in order to maintain
the programmed input current limit the charge time is
automatically increased. In other words, the charge time
is extended inversely proportional to charge current de-
livered to the battery. For Li-Ion and similar batteries that
require accurate nal oat potential, the internal bandgap
reference, voltage amplier and the resistor divider provide
regulation with ±0.8% accuracy.
Trickle Charge and Defective Battery Detection
At the beginning of a charge cycle, if the battery voltage
is low (below 2.8V) the charger goes into trickle charge
reducing the charge current to 10% of the full-scale cur-
rent. If the low battery voltage persists for one quarter
of the total charge time, the battery is assumed to be
defective, the charge cycle is terminated and the CHRG
pin output assumes a high impedance state. If for any
reason the battery voltage rises above ~2.8V the charge
cycle will be restarted. To restart the charge cycle (i.e. when
the dead battery is replaced with a discharged battery),
simply remove the input voltage and reapply it or cycle
the TIMER pin to 0V.
OPERATION
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4090EDJC#TRPBR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO22 |
| LTC6103CMS8#TR | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| LTC6103HMS8#TR | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| LTC6604CUFF-10#TRPBF | SPECIALTY ANALOG CIRCUIT, PQCC34 |
| LUC025F | 2-OUTPUT 16.5 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4085EDE-4#PBF | 功能描述:IC USB POWER MANAGER 14DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:* 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC4085EDE-4#TRPBF | 功能描述:IC USB POWER MANAGER 14DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:* 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC4085EDEPBF | 制造商:Linear Technology 功能描述:Li-Ion Charger + USB Power Mgr LTC4085 |
| LTC4085EDE-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:USB Power Manager with Ideal Diode Controller and Li-Ion Charger |
| LTC4085EDE-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:USB Power Manager with Ideal Diode Controller and Li-Ion Charger |
發布緊急采購，3分鐘左右您將得到回復。