- 您現在的位置：買賣IC網 > PDF目錄98003 > LTC4075HVXEDD#TR (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 PDF資料下載
參數資料
| 型號： | LTC4075HVXEDD#TR |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| 封裝： | 3 X 3 MM, 0.75 MM HEIGHT, PLASTIC, MO-229WEED-2, DFN-10 |
| 文件頁數： | 2/16頁 |
| 文件大小： | 170K |
| 代理商： | LTC4075HVXEDD#TR |
LTC4075HVX
10
4075hvxf
OPERATION
Automatic Recharge
In standby mode, the charger sits idle and monitors the
battery voltage using a comparator with a 4.1ms lter time
(tRECHRG). A charge cycle automatically restarts when the
battery voltage falls below 4.075V (which corresponds to
approximately 80% to 90% battery capacity). This ensures
that the battery is kept at, or near, a fully charged condi-
tion and eliminates the need for periodic charge cycle
initiations.
If the battery is removed from the charger, a sawtooth
waveform appears at the battery output. This is caused
by the repeated cycling between termination and recharge
events. This cycling results in pulsing at the CHRG output;
an LED connected to this pin will exhibit a blinking pattern,
indicating to the user that a battery is not present. The
frequency of the sawtooth is dependent on the amount
of output capacitance.
Manual Shutdown
The ENABLE pin has a 2MΩ pull-down resistor to GND. The
denition of this pin depends on which source is supplying
power. When the wall adapter input is supplying power,
logic low enables the charger and logic high disables it
(the internal pull-down resistor defaults the charger to the
charging state). The opposite is true when the USB input is
supplying power; logic low disables the charger and logic
high enables it (the default is the shutdown state).
The DCIN input draws 40μA when the charger is in shut-
down mode. The USBIN input draws 40μA during shutdown
if no voltage is applied to DCIN, but draws only 23μA when
VDCIN provides valid voltage (see Table 1).
Status Indicators
The charge status open drain output (CHRG) has two
states: pull-down and high impedance. The pull-down
state indicates that the LTC4075HVX is in a charge cycle.
Once the charge cycle has terminated or the LTC4075HVX
is disabled, the pin state becomes high impedance.
The power supply status open drain output (PWR) has
two states: pull-down and high impedance. The pull-down
state indicates that power is present at either DCIN or
USBIN. This output is strong enough to drive an LED. If no
valid voltage is applied at either pin, the PWR pin is high
impedance, indicating that the LTC4075HVX lacks valid
input voltage (see Table 1) to charge the battery.
Table 1. Power Source Selection
VUSBIN < 3.95V or
VUSBIN < BAT + 50mV
6V > VUSBIN > 3.95V and
VUSBIN > BAT + 50mV
22V > VUSBIN > 6V
ENABLE
HIGH
LOW or No Connect
HIGH
LOW or No Connect
HIGH
LOW or No Connect
VDCIN < 4.15V or
VDCIN < BAT + 50mV
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
Charging from
USBIN source.
PWR: LOW
USBPWR: Hi-Z
CHRG: LOW
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
6V > VDCIN > 4.15V
and VDCIN > BAT +
50mV
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
Charging from DCIN
source.
PWR: LOW
USBPWR: LOW
CHRG: LOW
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
Charging from DCIN
source.
PWR: LOW
USBPWR: LOW
CHRG: LOW
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
Charging from DCIN
source.
PWR: LOW
USBPWR: LOW
CHRG: LOW
22V > VDCIN > 6V
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4075HVXEDD | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC4080EMSE | 0.8 A BATTERY CHARGE CONTROLLER, 2750 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC4085EDE-3#TRPBF | POWER SUPPLY MANAGEMENT CKT, PDSO14 |
| LTC4090EDJC#TRPBR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO22 |
| LTC6103CMS8#TR | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4075X | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Input USB/AC Adapter Standalone Li-Ion Battery Chargers |
| LTC4075XEDD | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Input USB/AC Adapter Standalone Li-Ion Battery Chargers |
| LTC4076 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Input Standalone Li-Ion Battery Charger |
| LTC4076EDD | 功能描述:IC CHARG BATT LI-ON USB 10DFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC4076EDD#PBF | 功能描述:IC CHARG BATT LI-ON USB 10DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
發布緊急采購，3分鐘左右您將得到回復。