- 您現在的位置：買賣IC網 > PDF目錄44995 > LTC4065EDC-4.4#PBF (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 PDF資料下載
參數資料
| 型號： | LTC4065EDC-4.4#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| 封裝： | 2 X 2 MM, LEAD FREE, PLASTIC, MO-229WCCD-2, DFN-6 |
| 文件頁數： | 15/16頁 |
| 文件大?。?/td> | 178K |
| 代理商： | LTC4065EDC-4.4#PBF |
8
LTC4065-4.4
406544f
OPERATIO
U
The LTC4065-4.4 is a linear battery charger designed
primarily for charging single-cell lithium-ion batteries.
Featuring an internal P-channel power MOSFET, the charger
uses a constant-current/constant-voltage charge algo-
rithm with programmable current. Charge current can be
programmed up to 750mA with a final float voltage accu-
racy of
±0.6%. The CHRG open-drain status output indi-
cates if C/10 has been reached. No blocking diode or
external sense resistor is required; thus, the basic charger
circuit requires only two external components. An internal
termination timer and trickle charge low-battery condi-
tioning adhere to battery manufacturer safety guidelines.
Furthermore, the LTC4065-4.4 is capable of operating
from a USB power source.
An internal thermal limit reduces the programmed charge
current if the die temperature attempts to rise above a
preset value of approximately 115
°C. This feature protects
the LTC4065-4.4 from excessive temperature and allows
the user to push the limits of the power handling capability
of a given circuit board without risk of damaging the
LTC4065-4.4 or external components. Another benefit of
the LTC4065-4.4 thermal limit is that charge current can
be set according to typical, not worst-case, ambient tem-
peratures for a given application with the assurance that
the charger will automatically reduce the current in worst-
case conditions.
The charge cycle begins when the following conditions are
met: the voltage at the VCC pin exceeds 3.6V and approxi-
mately 80mV above the BAT pin voltage, a program
resistor is present from the PROG pin to ground and the EN
pin is pulled below the shutdown threshold (typically
0.82V).
If the BAT pin voltage is below 2.9V, the charger goes into
trickle charge mode, charging the battery at one-tenth the
programmed charge current to bring the cell voltage up to
a safe level for charging. If the BAT pin voltage is above
4.3V, the charger will not charge the battery as the cell is
near full capacity. Otherwise, the charger goes into the fast
charge constant-current mode.
When the BAT pin approaches the final float voltage
(4.4V), the LTC4065-4.4 enters constant-voltage mode
and the charge current begins to decrease. When the
current drops to 10% of the full-scale charge current, an
internal comparator turns off the N-channel MOSFET on
the CHRG pin and the pin assumes a high impedance state.
An internal timer sets the total charge time, tTIMER
(typically 4.5 hours). When this time elapses, the charge
cycle terminates and the CHRG pin assumes a high
impedance state. The charge cycle will automatically
restart if the BAT pin voltage falls below VRECHRG
(typically 4.3V). To restart the charge cycle, remove the
input voltage and reapply it, or momentarily force the EN
pin above VMS (typically 0.82V).
When the input voltage is not present, the battery drain
current is reduced to less than 4
A. The LTC4065-4.4 can
also be shut down by pulling the EN pin above the shutdown
threshold voltage.
Programming Charge Current
The charge current is programmed using a single resistor
from the PROG pin to ground. The battery charge current
is 1000 times the current out of the PROG pin. The
program resistor and the charge current are calculated
using the following equations:
R
V
I
V
R
PROG
CHG
PROG
==
1000
1
1000
,
The charge current out of the BAT pin can be determined
at any time by monitoring the PROG pin voltage and using
the following equation:
I
V
R
BAT
PROG
=
1000
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4070IDDB#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| LTC4070EMS8E#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| LTC4070EDDB#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| LTC4071EMS8E#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| LTC4071EDDB#TRMPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4065L | 制造商:LINEAR 制造商全稱:LINEAR 功能描述:Standalone 250mA Li-Ion Battery Charger in 2 × 2 DFN |
| LTC4065L_12 | 制造商:LINEAR 制造商全稱:LINEAR 功能描述:Standalone 250mA Li-Ion Battery Charger in 2 × 2 DFN |
| LTC4065LEDC#TRM | 制造商:Linear Technology 功能描述:BATT CHARGER LI ON 250MA 6DFN |
| LTC4065LEDC#TRMPBF | 功能描述:IC CHARGER LI-ION 6-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC4065LEDC#TRPBF | 功能描述:IC CHARGER LI-ION 6-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。