- 您現在的位置：買賣IC網 > PDF目錄44995 > LTC4001-1EUF#TRPBF (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 PDF資料下載
參數資料
| 型號： | LTC4001-1EUF#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 |
| 封裝： | 4 X 4 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, MO-220WGGC, QFN-16 |
| 文件頁數： | 3/20頁 |
| 文件大小： | 227K |
| 代理商： | LTC4001-1EUF#TRPBF |
11
LTC4001-1
40011f
The equations for calculating R1 (used in single resistor
programming) differ from the equations for calculating
RPROG and RIDET (2-resistor programming) and reflect the
fact that the current from both the IDET and PROG pins
must flow through a single resistor R1 when a single
programming resistor is used.
CHRG Status Output Pin
When a charge cycle starts, the CHRG pin is pulled to
ground by an internal N-channel MOSFET which is capable
of driving an LED. When the charge current drops below
the end-of-charge (IDET) threshold for at least 4ms, and
the battery voltage is close to the float voltage, the N-channel
MOSFET turns off and a weak 30
A current source to
ground is connected to the CHRG pin. This weak pull-
down remains until the charge cycle ends. After charging
ends, the pin will become high impedance. By using two
different value resistors, a microprocessor can detect
three states from this pin (charging, end-of-charge and
charging stopped). See Figure 2.
To detect the charge mode, force the digital output pin,
OUT, high and measure the voltage on the CHRG pin. The
N-channel MOSFET will pull the pin low even with a 2k pull-
up resistor. Once the charge current drops below the end-
of-charge threshold, the N-channel MOSFET is turned off
and a 30
A current source is connected to the CHRG pin.
The IN pin will then be pulled high by the 2k resistor
connected to OUT. Now force the OUT pin into a high
impedance state, the current source will pull the pin low
through the 390k resistor. When charging stops, the
CHRG pin changes to a high impedance state and the 390k
resistor will then pull the pin high to indicate charging has
stopped.
Charge Termination
Battery charging may be terminated several different ways,
depending on the connections made to the TIMER pin. For
time-based termination, connect a capacitor between the
TIMER pin and GNDSENS (CTIMER= Time(Hrs) 0.0733F).
Charging may be terminated when charge current drops
below the IDET threshold by tying TIMER to GNDSENS.
Finally, charge termination may be defeated by tying
TIMER to IDET. In this case, an external device can
terminate charging by pulling the EN pin high.
Battery Temperature Detection
When battery temperature is out of range (either too hot or
too cold) charging is temporarily halted and the FAULT pin
is driven high. In addition, if the battery is still charging at
a high rate (greater than the IDET current) when a tem-
perature fault occurs, the CHRG pin NMOS turns on and off
at approximately 50kHz, alternating between a high and
low duty factor at an approximate rate of 1.5Hz (Figure 3).
This provides a low rate visual indication (1.5Hz) when
driving an LED from the CHRG pin while providing a fast
temperature fault indication (20
s typical) to a micropro-
cessor by tying the CHRG pin to an interrupt line. Serra-
tions within this pulse are typically 500ns wide.
APPLICATIO S I FOR ATIO
WU
UU
Figure 2. Microprocessor Interface
Figure 3. CHRG Temperature Fault Waveform
LTC4001-1
VIN
VDD
IN
OUT
PROCESSOR
CHRG
R2
2k
R1
390k
40011 F02
20
s
40011 F03
667ms
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4009IUF#TRPBF | BATTERY CHARGE CONTROLLER, 633 kHz SWITCHING FREQ-MAX, PQCC20 |
| LTC4009IUF#PBF | BATTERY CHARGE CONTROLLER, 633 kHz SWITCHING FREQ-MAX, PQCC20 |
| LTC4009CUF-1#TRPBF | BATTERY CHARGE CONTROLLER, 633 kHz SWITCHING FREQ-MAX, PQCC20 |
| LTC4009CUF-2#TRPBF | BATTERY CHARGE CONTROLLER, 633 kHz SWITCHING FREQ-MAX, PQCC20 |
| LTC4009IUF-1#PBF | BATTERY CHARGE CONTROLLER, 633 kHz SWITCHING FREQ-MAX, PQCC20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4001EUF | 制造商:Linear Technology 功能描述:Battery Charger Li-Ion/Li-Pol 2000mA 4.2V 16-Pin QFN EP |
| LTC4001EUF#PBF | 功能描述:IC CHARGER LI-ION BUCK 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC4001EUF#TRPBF | 功能描述:IC CHARGER LI-ION BUCK 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC4001EUF-1#PBF | 功能描述:IC CHARGER LI-ION BUCK 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC4001EUF-1#PBF | 制造商:Linear Technology 功能描述:IC BATT CHARGER SW MODE 16QFN |
發布緊急采購，3分鐘左右您將得到回復。