參數資料
型號： LTC3816IUHF#PBF
廠商： LINEAR TECHNOLOGY CORP
元件分類： 穩壓器
英文描述： SWITCHING CONTROLLER, PQCC38
封裝： 5 X 7 MM, LEAD FREE, PLASTIC, MO-220WHKD, QFN-38
文件頁數： 10/44頁
文件大?。?/td> 753K
代理商： LTC3816IUHF#PBF
LTC3816
3816f
applicaTions inForMaTion
down mode by pulling the VRON pin below 0.65V. In the
shutdown mode, the internal circuitry and the INTVCC
regulator are off and the supply current drops well below
100A. When the VRON pin voltage is between 0.65V and
1.2V, the INTVCC regulator and internal circuitry power up
but the driver outputs remain low.
TOPSIDE MOSFET DRIVER SUPPLY
An external bootstrap capacitor, CB, connected from the
BOOST pin to the SW pin supplies the topside gate driver
as shown in Figure 1. Capacitor CB is charged though the
external diode, DB, from INTVCC when the SW pin is low.
When the topside MOSFET is turned on, the top driver
places the CB voltage across the gate source of the top
MOSFET. This enhances the MOSFET and turns on the
top switch. The switch node voltage, SW, rises to VIN and
the BOOST pin follows. With the topside MOSFET on, the
boost voltage is above the input supply:
VBOOST = VIN + VINTVCC
The value of the boost capacitor, CB, needs to be at least
100 times that of the total input capacitance of the topside
MOSFET. The reverse breakdown of the external Schottky
diode, DB, must be greater than VIN(MAX).
IMVP-6/IMVP-6.5 SELECTION AND VBOOT VOLTAGE
The LTC3816 can be configured to meet either IMVP-6
or IMVP-6.5 requirements. To select IMVP-6 operation,
short both IMONandPREIMONtoINTVCC.Atstart-up,when
VRON is asserted, the switcher output ramps to VBOOT =
1.2V regardless of the VID code. To configure IMVP-6.5
operation, connect a resistor from IMON to VSS(SEN) and
another resistor from PREIMON to ITC. The IMON and
PREIMON resistance set the IMON gain (see the IMON sec-
tion). The VBOOT voltage for IMVP-6.5 is 1.1V.
SOFT-START OPERATION
The start-up of VOUT is controlled by the LTC3816’s SS
pin. When the voltage at the SS pin is less than 1.3V, the
LTC3816 regulates the VFB voltage to the SS pin voltage
instead of 1.3V. This allows the user to program the soft-
start of the regulator output with a capacitor from the SS
pin to GND. An internal 1A current source charges this
capacitor, creating a voltage ramp on the SS pin. As the
SS pin voltage rises from 0V to 1.3V, the output voltage,
VOUT, rises smoothly from 0V to its VBOOT value. Once
the soft-start interval is over, the internal current source
continues charging the SS capacitor until the SS poten-
tial is internally clamped at about 2.7V. For the IMVP-6
configuration, a 1000pF SS capacitor generates roughly
a 1.6ms start-up time. With the IMVP-6.5 configuration,
the start-up time is about 1.5ms.
Duringsevereoverloadconditions,theLTC3816discharges
theSScapacitortolowertheswitcheroutputvoltage.Ifthe
potential at SS is forced below 0.3V, the controller reduces
its IMAX sourcing current from 10A to 2.5A and cuts the
short-circuit current to about 25% of its nominal value.
CURRENT SENSE AND CURRENT LIMIT
The LTC3816 features an onboard cycle-by-cycle user-
programmable current limit circuit that controls the peak
inductor current. The IMAX pin has an internal 10A pull-
up current source, allowing the maximum load current
ILOAD(MAX) to be programmed by a single external resistor
RIMAX connected between the IMAX and ISENN pins.
I
R
I
L PEAK
IMAX
SENSE
LOAD MAX
LIMIT
L
(
)
(
)
(
=
<
= PPEAK
L
IMAX
SENSE
L
I
R
I
) –
–
2
=
whereIL(PEAK)isthepeakinductorcurrent,IIMAXistheIMAX
pin pull-up current, RSENSE is the current sense resistor
value and
IL is the inductor ripple current.
I
f
L
V
L
OSC
OUT
IN
=
1
–
Note that the output ripple current varies with the switch-
ing frequency, inductor value and duty cycle. Hence, the
current limit value should be checked on the application
board to ensure that ILOAD(MAX)<ILIMITunderalloperating
conditions and temperature variations.
For current sensing using a low value sense resistor, the
sense resistor parasitic inductance must be considered to
相關PDF資料
PDF描述
LTC3816IFE#TRPBF SWITCHING CONTROLLER, PDSO38
LTC3816EFE#PBF SWITCHING CONTROLLER, PDSO38
LTC3816EFE#TRPBF SWITCHING CONTROLLER, PDSO38
LTC3823IGN#TRPBF 4 A SWITCHING CONTROLLER, PDSO28
LTC3851AEMSE-1#PBF 0.05 A SWITCHING CONTROLLER, 810 kHz SWITCHING FREQ-MAX, PDSO16
相關代理商/技術參數
參數描述
LTC3819EG#PBF 功能描述:IC CNTRLR STEP DOWN 36-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件
LTC3819EG#TRPBF 功能描述:IC CNTRLR STEP DOWN 36-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件
LTC3822EDD#PBF 功能描述:IC REG CTRLR BUCK PWM CM 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,000 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:1MHz 占空比:50% 電源電壓:9 V ~ 10 V 降壓:無 升壓:是 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 包裝:帶卷 (TR)
LTC3822EDD#TRPBF 功能描述:IC REG CTRLR BUCK PWM CM 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR)
LTC3822EDD-1#PBF 功能描述:IC REG CTRLR BUCK PWM CM 12-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*