- 您現在的位置：買賣IC網 > PDF目錄44992 > LTC3785IUF#PBF (LINEAR TECHNOLOGY CORP) 3 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC24 PDF資料下載
參數資料
| 型號： | LTC3785IUF#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 3 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC24 |
| 封裝： | 4 X 4 MM, LEAD FREE, PLASTIC, MO-220WGGD, QFN-24 |
| 文件頁數： | 17/20頁 |
| 文件大小： | 275K |
| 代理商： | LTC3785IUF#PBF |
LTC3785
3785fc
pin FuncTions
VSENSE (Pin 4): Overvoltage and Undervoltage Sense.
The overvoltage threshold is internally set 10% above
the regulated FB voltage and the undervoltage threshold
is internally set 6.5% below the FB regulated voltage. This
pin can be tied to FB but to optimize the response time it
is recommended that a voltage divider from VOUT be ap-
plied. The divider can be skewed from the feedback value
to achieve the desired UV or OV threshold.
ILSET (Pin 5): Current Limit Set. A resistor from this pin
to ground sets the current limit threshold from the ISVIN
and ISSW1 pins.
CCM (Pin 6): Continuous Conduction Mode Control Pin.
When set low, the inductor current is allowed to go slightly
negative (–15mV referenced to the ISVOUT – ISSW2 pins).
When driven high, the reverse current limit is set to the
similar value of the forward current limit set by the ILSET
pin.
RT(Pin7):OscillatorProgrammingPin.Aresistorfromthis
pin to GND sets the free-running frequency of the IC.
f
R
MHz
OSC
T
25000
MODE (Pin 8): Burst Mode Control Pin.
MODE = High: Enable Burst Mode Operation. In Burst
Mode operation the operation is variable frequency,
which provides a significant efficiency improvement
at light loads. The Burst Mode operation will continue
until the pin is driven low.
MODE=Low:DisableBurstModeoperationandmaintain
low noise, constant frequency operation.
NC (Pin 9): No Connect. There is no electrical connection
to this pin inside the package.
ISVOUT (Pin 10): Reverse Current Limit Comparator Non-
inverting Input. This pin is normally connected to the drain
of the N-channel MOSFET D (TG2 driven).
VBST2 (Pin 11): Boosted Floating Driver Supply for Boost
Switch D. This pin will swing from a diode below VCC up
to VOUT + VCC – VDIODE.
SW2 (Pin 13): Ground Reference for Driver D. Gate drive
from TG2 will reference to the common point of output
switches C and D.
ISSW2 (Pin 14): Reverse Current Limit Comparator Invert-
ing Input. This pin is normally connected to the source of
the N-channel MOSFET D (TG2 driven).
VDRV (Pin 16): Driver Supply for Ground Referenced
Switches. Connect this pin to VCC potential.
BG1, BG2 (Pins 17, 15): Bottom gate driver pins drive
the ground referenced N-channel MOSFET switches B
and C.
ISSW1 (Pin 18): Forward Current Limit Comparator Non-
inverting Input. This pin is normally connected to the
source of the N-channel MOSFET A (TG1 driven).
SW1 (Pin 19): Ground Reference for Driver A. Gate drive
from TG1 will reference to the common point of output
switches A and B.
TG1, TG2 (Pins 20, 12): Top gate drive pins drive the
top N-channel MOSFET switches A and D with a voltage
swing equal to VCC – VDIODE superimposed on the SW1
and SW2 nodes respectively.
VBST1 (Pin 21): Boosted Floating Driver Supply for the
Buck Switch A. This pin will swing from a diode below
VCC up to VIN + VCC – VDIODE.
ISVIN (Pin 22): Forward Current Limit Comparator Invert-
ing Input. This pin is normally connected to the drain of
N-channel MOSFET A (TG1 driven).
VCC (Pin 23): Internal 4.35V LDO Regulator Output. The
driver and control circuits are powered from this voltage
to limit the maximum VGS drive voltage. Decouple this pin
to power ground with at least a 4.7F ceramic capacitor.
For low VIN applications, VCC can be bootstrapped from
VOUT through a Schottky diode.
VIN (Pin 24): Input Supply Pin for the VCC Regulator. A
ceramic capacitor of at least 10F is recommended close
to the VIN and GND pins.
Ground (Exposed Pad Pin 25): The GND and PGND pins
are connected to the exposed pad which must be con-
nected to the PCB ground for electrical contact and rated
thermal performance.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3785EUF | 3 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC24 |
| LTC3786IMSE#TRPBF | SWITCHING CONTROLLER, 900 kHz SWITCHING FREQ-MAX, PDSO16 |
| LTC3786EMSE#TRPBF | SWITCHING CONTROLLER, 900 kHz SWITCHING FREQ-MAX, PDSO16 |
| LTC3786EMSE#PBF | SWITCHING CONTROLLER, 900 kHz SWITCHING FREQ-MAX, PDSO16 |
| LTC3786EUD#PBF | SWITCHING CONTROLLER, 900 kHz SWITCHING FREQ-MAX, PQCC16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3786EMSE#PBF | 功能描述:IC REG CTRLR BST PWM CM 16-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 特色產品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 標準包裝:1 系列:PowerWise® PWM 型:電壓模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.5 V ~ 18 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-5°C ~ 125°C 封裝/外殼:32-WFQFN 裸露焊盤 包裝:Digi-Reel® 產品目錄頁面:1303 (CN2011-ZH PDF) 其它名稱:LM3754SQDKR |
| LTC3786EMSE#PBF | 制造商:Linear Technology 功能描述:IC DC-DC CONV 550kHz MSOP16 制造商:Linear Technology 功能描述:IC, DC-DC CONV, 550kHz, MSOP16 |
| LTC3786EMSE#TRPBF | 功能描述:IC REG CTRLR BST PWM CM 16-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC3786EUD#PBF | 功能描述:IC REG CTRLR BST PWM CM 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 特色產品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 標準包裝:1 系列:PowerWise® PWM 型:電壓模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.5 V ~ 18 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-5°C ~ 125°C 封裝/外殼:32-WFQFN 裸露焊盤 包裝:Digi-Reel® 產品目錄頁面:1303 (CN2011-ZH PDF) 其它名稱:LM3754SQDKR |
| LTC3786EUD#PBF | 制造商:Linear Technology 功能描述:IC, DC-DC CONV, 550kHz, QFN16 |
發布緊急采購，3分鐘左右您將得到回復。