- 您現在的位置：買賣IC網 > PDF目錄44992 > LTC3633EUFD#TRPBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, PQCC28 PDF資料下載
參數資料
| 型號： | LTC3633EUFD#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, PQCC28 |
| 封裝： | 4 X 5 MM, LEAD FREE, PLASTIC, MO-220, QFN-28 |
| 文件頁數： | 27/28頁 |
| 文件大?。?/td> | 384K |
| 代理商： | LTC3633EUFD#TRPBF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁
LTC3633
8
3633f
PIN FUNCTIONS
PGOOD1 (Pin 1/Pin 4): Channel 1 Open-Drain Power
Good Output Pin. PGOOD1 is pulled to ground when the
voltage on the VFB1 pin is not within ±8% (typical) of the
internal 0.6V reference. PGOOD1 becomes high imped-
ance once the VFB1 pin returns to within ±5% (typical) of
the internal reference.
PHMODE (Pin 2/Pin 5): Phase Select Input. Tie this pin
to ground to force both channels to switch in phase. Tie
this pin to INTVCC to force both channels to switch 180°
out of phase. Do not oat this pin.
RUN1 (Pin 3/Pin 6): Channel 1 Regulator Enable Pin.
Enables channel 1 operation by tying RUN above 1.22V.
Tying it below 1V places the part into shutdown. Do not
oat this pin.
MODE/SYNC (Pin 4/Pin 7): Mode Select and External
Synchronization Input. Tie this pin to ground to force
continuous synchronous operation at all output loads.
Floating this pin or tying it to INTVCC enables high efciency
Burst Mode operation at light loads. Drive this pin with a
clock to synchronize the LTC3633 switching. An internal
phase-locked loop will force the bottom power NMOS’s
turn on signal to be synchronized with the rising edge of
the CLKIN signal. When this pin is driven with a clock,
forced continuous mode is automatically selected.
RT (Pin 5/Pin 8): Oscillator Frequency Program Pin.
Connect an external resistor (between 80k to 640k) from
this pin to SGND in order to program the frequency from
500kHz to 4MHz. When RT is tied to INTVCC, the switching
frequency will default to 2MHz.
RUN2 (Pin 6/Pin 9): Channel 2 Regulator Enable Pin.
Enables channel 2 operation by tying RUN above 1.22V.
Tying it below 1V places the part into shutdown. Do not
oat this pin.
SGND (Pin 7/Pin 10): Signal Ground Pin. This pin should
have a low noise connection to reference ground. The
feedback resistor network, external compensation network,
and RT resistor should be connected to this ground.
PGOOD2 (Pin 8/Pin 11): Channel 2 Open-Drain Power
Good Output Pin. PGOOD2 is pulled to ground when the
voltage on the VFB2 pin is not within 8% (typical) of the
internal 0.6V reference. PGOOD2 becomes high imped-
ance once the VFB2 pin returns to within ±5% (typical) of
the internal reference.
VFB2 (Pin 9/Pin 12): Channel 2 Output Feedback Voltage
Pin. Input to the error amplier that compares the feedback
voltage to the internal 0.6V reference voltage. Connect this
pin to a resistor divider network to program the desired
output voltage.
TRACKSS2 (Pin 10/Pin 13): Output Tracking and Soft-Start
Input Pin for Channel 2. Forcing a voltage below 0.6V on
this pin bypasses the internal reference input to the error
amplier. The LTC3633 will servo the FB pin to the TRACK
voltage under this condition. Above 0.6V, the tracking func-
tion stops and the internal reference resumes control of
the error amplier. An internal 1.4μA pull up current from
INTVCC allows a soft start function to be implemented by
connecting a capacitor between this pin and SGND.
ITH2 (Pin 11/Pin 14): Channel 2 Error Amplier Output
and Switching Regulator Compensation Pin. Connect this
pin to appropriate external components to compensate
the regulator loop frequency response. Connect this pin
to INTVCC to use the default internal compensation.
VON2 (Pin 12/Pin 15): On-Time Voltage Input for Chan-
nel 2. This pin sets the voltage trip point for the on-time
comparator. Tying this pin to the output voltage makes
the on-time proportional to VOUT2 when VOUT2 < 6V. When
VOUT2 > 6V, switching frequency may become higher
than the set frequency. The pin impedance is nominally
180kΩ.
SW2 (Pins 13, 14/Pins 16, 17): Channel 2 Switch Node
Connection to External Inductor. Voltage swing of SW is
from a diode voltage drop below ground to VIN.
VIN2 (Pins 15, 16/Pins 18, 19): Power Supply Input for
Channel 2. Input voltage to the on chip power MOSFETs
on channel 2. This input is capable of operating from a
different supply voltage than VIN1.
BOOST2 (Pin 17/Pin 20): Boosted Floating Driver Supply
for Channel 2. The (+) terminal of the bootstrap capacitor
connects to this pin while the (–) terminal connects to
the SW pin. The normal operation voltage swing of this
pin ranges from a diode voltage drop below INTVCC up
to VIN+INTVCC.
(QFN/TSSOP)
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3634EUFD#PBF | 5.5 A DUAL SWITCHING CONTROLLER, 4600 kHz SWITCHING FREQ-MAX, PQCC28 |
| LTC3634EFE#TRPBF | 5.5 A DUAL SWITCHING CONTROLLER, 4600 kHz SWITCHING FREQ-MAX, PDSO28 |
| LTC3634EFE#PBF | 5.5 A DUAL SWITCHING CONTROLLER, 4600 kHz SWITCHING FREQ-MAX, PDSO28 |
| LTC3642IMS8E-3.3E#PBF | 0.13 A SWITCHING REGULATOR, PDSO8 |
| LTC3672BEDC-2#PBF | 1.1 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3633IFE#PBF | 功能描述:IC REG BUCK ADJ 3A DL 28TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LTC3633IFE#TRPBF | 功能描述:IC REG BUCK ADJ 3A DL 28TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LTC3633IUFD#PBF | 功能描述:IC REG BUCK ADJ 3A DL 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:MIC23xxx HyperLight Load™ Regulators 標準包裝:5,000 系列:HyperLight Load® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.8V 輸入電壓:2.7 V ~ 5.5 V PWM 型:混合物 頻率 - 開關:4MHz 電流 - 輸出:2A 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-VFDFN 裸露焊盤，8-MLF? 包裝:帶卷 (TR) 供應商設備封裝:8-MLF?（2x2） 產品目錄頁面:1094 (CN2011-ZH PDF) 其它名稱:576-3303-2 |
| LTC3633IUFD#TRPBF | 功能描述:IC REG BUCK ADJ 3A DL 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LTC3633IUFDPBF | 制造商:Linear Technology 功能描述:Conv DC-DC Dual Step-Down 3.6-15V QFN28 |
發布緊急采購，3分鐘左右您將得到回復。