- 您現在的位置：買賣IC網 > PDF目錄44992 > LTC3611EWP (LINEAR TECHNOLOGY CORP) 10 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PQCC64 PDF資料下載
參數資料
| 型號： | LTC3611EWP |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 10 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PQCC64 |
| 封裝： | 9 X 9 MM, PLASTIC, QFN-64 |
| 文件頁數： | 11/26頁 |
| 文件大?。?/td> | 411K |
| 代理商： | LTC3611EWP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
LTC3611
3611fd
ApplicAtions inForMAtion
How to Reduce SW Ringing
As with any switching regulator, there will be voltage ring-
ing on the SW node, especially for high input voltages.
The ringing amplitude and duration is dependent on the
switching speed (gate drive), layout (parasitic inductance)
and MOSFET output capacitance. This ringing contributes
to the overall EMI, noise and high frequency ripple. One
way to reduce ringing is to optimize layout. A good layout
minimizesparasiticinductance.AddingRCsnubbersfrom
SW to GND is also an effective way to reduce ringing.
Finally, adding a resistor in series with the BOOST pin
will slow down the MOSFET turn-on slew rate to dampen
ringing, but at the cost of reduced efciency. Note that
since the IC is buffered from the high frequency transients
by PCB and bondwire inductances, the ringing by itself is
normally not a concern for controller reliability.
PC Board Layout Checklist
When laying out a PC board follow one of the two sug-
gested approaches. The simple PC board layout requires
a dedicated ground plane layer. Also, for higher currents,
a multilayer board is recommended to help with heat
sinking of power components.
The ground plane layer should not have any traces and
it should be as close as possible to the layer with the
LTC3611.
Place CIN and COUT all in one compact area, close to
the LTC3611. It may help to have some components
on the bottom side of the board.
Keep small-signal components close to the LTC3611.
Ground connections (including LTC3611 SGND and
PGND) should be made through immediate vias to
the ground plane. Use several larger vias for power
components.
Useacompactplanefortheswitchnode(SW)toimprove
cooling of the MOSFETs and to keep EMI down.
Use planes for VIN and VOUT to maintain good voltage
ltering and to keep power losses low.
Flood all unused areas on all layers with copper. Flood-
ing with copper reduces the temperature rise of power
components. Connect these copper areas to any DC
net (VIN, VOUT, GND or to any other DC rail in your
system).
When laying out a printed circuit board without a ground
plane, use the following checklist to ensure proper opera-
tion of the controller. These items are also illustrated in
Figure 7.
Segregate the signal and power grounds. All small-
signal components should return to the SGND pin at
one point, which is then tied to the PGND pin.
Connect the input capacitor(s), CIN,closetotheIC.This
capacitor carries the MOSFET AC current.
Keep the high dV/dT SW, BOOST and TG nodes away
from sensitive small-signal nodes.
ConnecttheINTVCCdecouplingcapacitor,CVCC,closely
to the INTVCC and PGND pins.
Connect the top driver boost capacitor, CB, closely to
the BOOST and SW pins.
Connect the VIN pin decoupling capacitor, CF, closely
to the VIN and PGND pins.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3616IUDD#TRPBF | 13.5 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PQCC24 |
| LTC3617EUDD#PBF | 14 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PQCC24 |
| LTC3618EUF#TRPBF | 8 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PQCC24 |
| LTC3618IFE#PBF | 8 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO24 |
| LTC3618EFE#TRPBF | 8 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3611EWP#PBF | 功能描述:IC REG BUCK SYNC ADJ 10A 64QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LTC3611EWP#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 10A 64QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LTC3611IWP#PBF | 功能描述:IC REG BUCK SYNC ADJ 10A 64QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LTC3611IWP#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 10A 64QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LTC3612EFE#PBF | 功能描述:IC REG BUCK SYNC ADJ 3A 20TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
發布緊急采購，3分鐘左右您將得到回復。