- 您現在的位置：買賣IC網 > PDF目錄44991 > LTC3560IS6#TRPBF (LINEAR TECHNOLOGY CORP) 2.1 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO6 PDF資料下載
參數資料
| 型號： | LTC3560IS6#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 2.1 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO6 |
| 封裝： | 1 MM HEIGHT, LEAD FREE, PLASTIC, MO-193, TSOT-23, 6 PIN |
| 文件頁數： | 16/16頁 |
| 文件大?。?/td> | 256K |
| 代理商： | LTC3560IS6#TRPBF |
LTC3560
9
3560fb
APPLICATIONS INFORMATION
more than powdered iron core inductors with similar
electrical characteristics. The choice of which style
inductor to use often depends more on the price versus
size requirements and any radiated eld/EMI requirements
than on what the LTC3560 requires to operate. Table 1
shows some typical surface mount inductors that work
well in LTC3560 applications.
CIN and COUT Selection
In continuous mode, the source current of the top MOSFET
is a square wave of duty cycle VOUT/VIN. To prevent large
voltage transients, a low ESR input capacitor sized for the
maximum RMS current must be used. The maximum RMS
capacitor current is given by:
C
IN required IRMS IOMAX
V
OUT VIN VOUT
()
1/ 2
V
IN
This formula has a maximum at VIN = 2VOUT, where
IRMS = IOUT/2. This simple worst-case condition is
commonly used for design because even signicant
deviations do not offer much relief. Note that the capacitor
manufacturer’s ripple current ratings are often based on
2000 hours of life. This makes it advisable to further
derate the capacitor, or choose a capacitor rated at a
higher temperature than required. Always consult the
manufacturer if there is any question.
The selection of COUT is driven by the required effective
seriesresistance(ESR).Typically,oncetheESRrequirement
for COUT has been met, the RMS current rating generally
far exceeds the IRIPPLE(P-P) requirement. The output ripple
ΔVOUT is determined by:
VOUT
IL ESR +
1
8fCOUT
where f = operating frequency, COUT = output capacitance
and ΔIL = ripple current in the inductor. For a xed output
voltage, the output ripple is highest at maximum input
voltage since ΔIL increases with input voltage.
If tantalum capacitors are used, it is critical that the capaci-
tors are surge tested for use in switching power supplies.
An excellent choice is the AVX TPS series of surface mount
tantalum. These are specially constructed and tested for low
ESR so they give the lowest ESR for a given volume. Other
capacitor types include Sanyo POSCAP, Kemet T510 and
T495 series, and Sprague 593D and 595D series. Consult
the manufacturer for other specic recommendations.
Using Ceramic Input and Output Capacitors
Higher values, lower cost ceramic capacitors are now
becoming available in smaller case sizes. Their high ripple
current, high voltage rating and low ESR make them
ideal for switching regulator applications. Because the
LTC3560’s control loop does not depend on the output
capacitor’s ESR for stable operation, ceramic capacitors
can be used freely to achieve very low output ripple and
small circuit size.
However, care must be taken when ceramic capacitors
are used at the input and the output. When a ceramic
capacitor is used at the input and the power is supplied
by a wall adapter through long wires, a load step at the
output can induce ringing at the input, VIN. At best, this
ringing can couple to the output and be mistaken as loop
instability. At worst, a sudden inrush of current through
the long wires can potentially cause a voltage spike at VIN,
large enough to damage the part.
When choosing the input and output ceramic capacitors,
choose the X5R or X7R dielectric formulations. These
dielectrics have the best temperature and voltage charac-
teristics of all the ceramics for a given value and size.
Output Voltage Programming
The output voltage is set by a resistive divider according
to the following formula:
VOUT = 0.6V 1+
R2
R1
(2)
The external resistive divider is connected to the output,
allowing remote voltage sensing as shown in Figure 2.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3563EDC | 1.75 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC3568EDD#TR | 4 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3568IDD | 4 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3568IDD#TR | 4 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3569IFE#PBF | 2.5 A SWITCHING REGULATOR, 3000 kHz SWITCHING FREQ-MAX, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3561 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1A, 4MHz, Synchronous Step-Down DC/DC Converter |
| LTC3561A | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1A, 4MHz, Synchronous Step-Down DC/DC Converter |
| LTC3561AEDD#PBF | 功能描述:IC REG BUCK SYNC ADJ 1A 8DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LTC3561AEDD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 1A 8DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LTC3561AEDD-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1A, 4MHz, Synchronous Step-Down DC/DC Converter |
發布緊急采購，3分鐘左右您將得到回復。