- 您現在的位置：買賣IC網 > PDF目錄44991 > LTC3538EDCB (LINEAR TECHNOLOGY CORP) 0.8 A SWITCHING REGULATOR, 1200 kHz SWITCHING FREQ-MAX, PDSO8 PDF資料下載
參數資料
| 型號： | LTC3538EDCB |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.8 A SWITCHING REGULATOR, 1200 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | 2 X 3 MM, PLASTIC, DFN-8 |
| 文件頁數： | 3/16頁 |
| 文件大小： | 206K |
| 代理商： | LTC3538EDCB |
LTC3538
11
3538fb
Since the output current is discontinuous in boost mode,
the ripple in this mode will generally be much larger than
the magnitude of the ripple in buck mode.
Minimizing solution size is usually a priority. Please be
aware that ceramic capacitors can exhibit a signicant
reduction in effective capacitance when a bias is applied.
The capacitors exhibiting the highest reduction are those
packaged in the smallest case size.
Input Capacitor Selection
Since VIN is the supply voltage for the IC it is recommended
to place at least a 4.7μF, low ESR ceramic bypass capaci-
tor close to VIN and GND. It is also important to minimize
any stray resistance from the converter to the battery or
other power source.
Optional Schottky Diodes
Schottky diodes across the synchronous switches B and
D are not required, but do provide a lower drop during the
break-before-make time (typically 15ns), thus improving
efciency. Use a surface mount Schottky diode such as an
MBRM120T3 or equivalent. Do not use ordinary rectier
diodes since their slow recovery times will compromise
efciency.
Table 2. Capacitor Vendor Information
SUPPLIER PHONE
FAX
WEB SITE
AVX
(803) 448-9411 (803) 448-1943 www.avxcorp.com
Sanyo
(619) 661-6322 (619) 661-1055 www.sanyovideo.com
Taiyo
Yuden
(408) 573-4150 (408) 573-4159 www.t-yuden.com
TDK
(847) 803-6100 (847) 803-6296 www.component.tdk.com
Shutdown MOSFET Selection
A discrete external N-channel MOSFET, open-drain pull-
down device or other suitable means can be used to put
the part in shutdown by pulling VC below 0.25V. Since
the error amplier sources 13μA typically when active
and 1.5μA in shutdown, a relatively high resistance pull-
down device can be used to pull VC below 0.25V. More
OPERATION
importantly, leakage and parasitic capacitance need to
be minimized. During start-up, 1.5μA is typically sourced
from VC. The leakage of an external pull-down device and
compensation components tied to VC, must therefore be
minimized to ensure proper start-up. Capacitance from
the pull-down device should also be minimized as it can
affect converter stability. An N-channel MOSFET such as
the FDV301N or similar is recommended if an external
discrete N-channel MOSFET is needed.
PCB Layout Considerations
The LTC3538 switches large currents at high frequencies.
Special care should be given to the PCB layout to ensure
stable, noise-free operation. Figure 3 depicts the recom-
mended PCB layout to be utilized for the LTC3538. A few
key guidelines follow:
1. All circulating current paths should be kept as short as
possible. This can be accomplished by keeping the routes
to all components (except the FB divider network) in
Figure 3 as short and as wide as possible. Capacitor ground
connections should via down to the ground plane in the
shortest route possible. The bypass capacitor on VINshould
be placed as close to the IC as possible and should have
the shortest possible paths to ground.
2. The small signal ground pad (GND) should have a single
point connection to the power ground. A convenient way
to achieve this is to short this pin directly to the Exposed
Pad as shown in Figure 3.
3. The components in bold and their connections should
all be placed over a complete ground plane.
4. To prevent large circulating currents from disrupting
the output voltage sensing, the ground for the resistor
divider should be returned directly to the small signal
ground (GND) as shown.
5. Use of vias in the attach pad will enhance the thermal
environment of the converter especially if the vias extend
to a ground plane region on the exposed bottom surface
of the PCB.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3538EDCB#TR | 0.8 A SWITCHING REGULATOR, 1200 kHz SWITCHING FREQ-MAX, PDSO8 |
| LTC3541EDD-2 | 1.25 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3541EDD-2#TR | 1.25 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3541EDD-3 | 1.25 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3541EDD-3#TR | 1.25 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3538EDCB#PBF | 制造商:Linear Technology 功能描述:DC-DC CONV BUCK/BOOST 8000mA DFN-8 制造商:Linear Technology 功能描述:DC-DC CONV, BUCK/BOOST, 8000mA, DFN-8 制造商:Linear Technology 功能描述:DC-DC CONV, BUCK/BOOST, 8000mA, DFN-8, Primary Input Voltage:5.5V, No. of Outputs:1, Output Current:800mA, No. of Pins:8, Operating Temperature Min:-40C, Operating Temperature Max:85C, MSL:MSL 1 - Unlimited, Package / Case:8-DFN , RoHS Compliant: Yes 制造商:Linear Technology 功能描述:DP-SWREG/Monolithic, Cut Tape 800mA, 1MHz Wide Input Voltage Synch Buck-Boost DC |
| LTC3538EDCB#TRMPBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 8DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LTC3538EDCB#TRPBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 8DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LTC3538EDCB-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:800mA Synchronous Buck-Boost DC/DC Converter |
| LTC3538EDCB-TR | 制造商:LINER 制造商全稱:Linear Technology 功能描述:800mA Synchronous Buck-Boost DC/DC Converter |
發布緊急采購，3分鐘左右您將得到回復。