- 您現在的位置：買賣IC網 > PDF目錄44991 > LTC3526BEDC (LINEAR TECHNOLOGY CORP) 0.5 A SWITCHING CONTROLLER, 1300 kHz SWITCHING FREQ-MAX, PDSO6 PDF資料下載
參數資料
| 型號： | LTC3526BEDC |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.5 A SWITCHING CONTROLLER, 1300 kHz SWITCHING FREQ-MAX, PDSO6 |
| 封裝： | 2 X 2 MM, 0.75 MM HEIGHT, PLASTIC, MO-229WCCD-2, DFN-6 |
| 文件頁數： | 16/16頁 |
| 文件大?。?/td> | 731K |
| 代理商： | LTC3526BEDC |
LTC3526/LTC3526B
9
3526a
Zero Current Comparator
The zero current comparator monitors the inductor cur-
rent to the output and shuts off the synchronous rectier
when this current reduces to approximately 30mA. This
prevents the inductor current from reversing in polarity,
improving efciency at light loads.
Synchronous Rectier
To control inrush current and to prevent the inductor
current from running away when VOUT is close to VIN, the
P-channel MOSFET synchronous rectier is only enabled
when VOUT > (VIN + 0.24V).
Anti-Ringing Control
The anti-ringing control connects a resistor across the
inductor to prevent high frequency ringing on the SW pin
during discontinuous current mode operation. Although
the ringing of the resonant circuit formed by L and CSW
(capacitance on SW pin) is low energy, it can cause EMI
radiation.
Output Disconnect
The LTC3526/LTC3526B are designed to allow true output
disconnect by eliminating body diode conduction of the
internal P-channel MOSFET rectier. This allows for VOUT
to go to zero volts during shutdown, drawing no current
from the input source. It also allows for inrush current
limiting at turn-on, minimizing surge currents seen by the
input supply. Note that to obtain the advantages of output
disconnect, there must not be an external Schottky diode
connected between the SW pin and VOUT. The output dis-
connect feature also allows VOUTtobepulledhigh,without
any reverse current into a battery connected to VIN.
Thermal Shutdown
If the die temperature exceeds 160°C, the LTC3526/
LTC3526B will go into thermal shutdown. All switches
will be off and the soft-start capacitor will be discharged.
The device will be enabled again when the die temperature
drops by about 15°C.
Burst Mode OPERATION
The LTC3526 will automatically enter Burst Mode opera-
tion at light load and return to xed frequency PWM mode
when the load increases. Refer to the Typical Performance
Characteristics to see the output load Burst Mode thresh-
old current vs VIN. The load current at which Burst Mode
operation is entered can be changed by adjusting the
inductor value. Raising the inductor value will lower the
load current at which Burst Mode operation is entered.
In Burst Mode operation, the LTC3526 still switches at a
xed frequency of 1MHz, using the same error amplier
and loop compensation for peak current mode control.
This control method eliminates any output transient
when switching between modes. In Burst Mode opera-
tion, energy is delivered to the output until it reaches the
nominal regulation value, then the LTC3526 transitions to
sleep mode where the outputs are off and the LTC3526
consumes only 9A of quiescent current from VOUT.When
the output voltage droops slightly, switching resumes.
Thismaximizesefciencyatverylightloadsbyminimizing
switchingandquiescentlosses.BurstModeoutputvoltage
ripple, which is typically 1% peak-to-peak, can be reduced
by using more output capacitance (10F or greater), or
with a small capacitor (10pF to 50pF) connected between
VOUT and FB.
As the load current increases, the LTC3526 will automati-
cally leave Burst Mode operation. Note that larger output
capacitorvaluesmaycausethistransitiontooccuratlighter
loads. Once the LTC3526 has left Burst Mode operation
and returned to normal operation, it will remain there until
the output load is reduced below the burst threshold.
Burst Mode operation is inhibited during start-up and soft-
start and until VOUT is at least 0.24V greater than VIN.
The LTC3526B features continuous PWM operation at
1MHz. At very light loads, the LTC3526B will exhibit
pulse-skip operation.
OPERATIO
U
(Refer to Block Diagram)
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3526LBEDC-2#PBF | SWITCHING REGULATOR, 2400 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC3526LEDC-2#PBF | SWITCHING REGULATOR, 2400 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC3526LBEDC-2#TRPBF | SWITCHING REGULATOR, 2400 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC3526LEDC#PBF | 0.55 A SWITCHING CONTROLLER, 1250 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC3527EUD | 0.8 A DUAL SWITCHING CONTROLLER, 2800 kHz SWITCHING FREQ-MAX, PQCC16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3526BEDC#PBF | 制造商:Linear Technology 功能描述:BOOST 0.85VMIN 1.5-5.25V 0.5A 6DFN 制造商:Linear Technology 功能描述:BOOST, 0.85VMIN, 1.5-5.25V, 0.5A, 6DFN 制造商:Linear Technology 功能描述:DP-SWREG/Monolithic, Cut Tape 500mA Low Vout Synchronous Boost w/disconnect 制造商:Linear Technology 功能描述:IC, DC-DC CONV, DFN-6, Primary Input Voltage:6V, No. of Outputs:1, Output Voltage:5.25V, Output Current:500mA, No. of Pins:6, Operating Temperature Min:-40C, Operating Temperature Max:85C, MSL:MSL 1 - Unlimited , RoHS Compliant: Yes |
| LTC3526BEDC#PBF | 制造商:Linear Technology 功能描述:IC DC-DC CONV DFN-6 制造商:Linear Technology 功能描述:IC, DC-DC CONV, DFN-6 |
| LTC3526BEDC#TRMPBF | 功能描述:IC REG BOOST SYNC ADJ 0.5A 6DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LTC3526BEDC#TRPBF | 功能描述:IC REG BOOST SYNC ADJ 0.5A 6DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LTC3526BEDC-2#TRMPBF | 功能描述:IC REG BOOST SYNC ADJ 0.5A 6DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
發布緊急采購，3分鐘左右您將得到回復。