參數資料
型號： LTC3521IUF#PBF
廠商： LINEAR TECHNOLOGY CORP
元件分類： 穩壓器
英文描述： SWITCHING REGULATOR, 1350 kHz SWITCHING FREQ-MAX, PQCC24
封裝： 4 X 4 MM, LEAD FREE, PLASTIC, MO-220WGGD, QFN-24
文件頁數： 20/22頁
文件大?。?/td> 1476K
代理商： LTC3521IUF#PBF
LTC3521
7
3521fa
PIN FUNCTIONS
FB3 (Pin 1/Pin 23): Feedback Voltage for the Buck Con-
verter Derived from a Resistor Divider Connected to the
Buck VOUT3 Output Voltage. The buck output voltage is
given by the following equation, where R1 is a resistor
between FB3 and ground, and R2 is a resistor between
FB3 and the buck output voltage:
VOUT3 = 0.6V 1+
R2
R1
FB2 (Pin 2/Pin 24): Feedback Voltage for the Buck Con-
verter Derived from a Resistor Divider Connected to the
Buck VOUT2 Output Voltage. The buck output voltage is
given by the following equation, where R1 is a resistor
between FB2 and ground, and R2 is a resistor between
FB2 and the buck output voltage:
VOUT2 = 0.6V 1+
R2
R1
SHDN2 (Pin 3/Pin 1): Forcing this pin above 1.4V enables
the buck converter output at SW2. Forcing this pin below
0.4V disables the buck converter. This pin cannot be left
floating.
PGOOD3 (Pin 4/Pin 2): This pin is an open-drain output
which pulls low under any of the following conditions:
VOUT3 buck output voltage is out of regulation, the part is
in overtemperature shutdown, the part is in undervoltage
lockout, or the SHDN3 pin is pulled low.
PGOOD2 (Pin 5/Pin 3): This pin is an open-drain output
which pulls low under any of the following conditions:
VOUT2 buck output voltage is out of regulation, the part is
in overtemperature shutdown, the part is in undervoltage
lockout, or the SHDN2 pin is pulled low.
PGOOD1 (Pin 6/Pin 4): This pin is an open-drain output
which pulls low under any of the following conditions:
VOUT1 buck-boost output voltage is out of regulation, the
part is in overtemperature shutdown, the part is in un-
dervoltage lockout, the buck-boost converter is in current
limit, or the SHDN1 pin is pulled low. See the Operation
section of this data sheet for details on the functionality
of this pin in PWM mode.
VIN (Pin 7/Pin 5): Low Current Power Supply Connection
Used to Power the Internal Circuitry of the LTC3521. This
pin should be bypassed by a 4.7F, or larger, ceramic
capacitor. The bypass capacitor should be placed as close
to the pin as possible and should have a short return path
to ground. Pins VIN, PVIN1, and PVIN2 must be connected
together in the application circuit.
GND (Pin 8/Pin 6): Small Signal Ground. This pin is
used as a ground reference for the internal circuitry of
the LTC3521.
PWM (Pin 9/Pin 7): Logic Input Used to Choose Between
Burst Mode Operation and PWM Mode for All Three Con-
verters. This pin cannot be left floating.
PWM = Low: Burst Mode operation is enabled on all
three converters. The buck converters will operate in
Burst Mode operation at light current but will automati-
cally transition to PWM operation at high currents. The
buck converters can supply maximum output current
(600mA) in this mode. The buck-boost converter will
operate in variable frequency mode and can only supply
a reduced load current (typically 50mA).
PWM = High: All three converters are forced into PWM
mode operation. The buck converters will remain at
constant-frequency operation until their minimum on-
time is reached. The buck-boost converter will remain
in PWM mode at all load currents.
FB1 (Pin 10/Pin 8): Feedback Voltage for the Buck-Boost
Converter Derived from a Resistor Divider on the Buck-
Boost Output Voltage. The buck-boost output voltage is
given by the following equation, where R1 is a resistor
between FB1 and ground, and R2 is a resistor between
FB1 and the buck output voltage:
VOUT1 = 0.6V 1+
R2
R1
SHDN3 (Pin 11/Pin 9): Forcing this pin above 1.4V en-
ables the buck converter output at SW3. Forcing this pin
below 0.4V disables the buck converter. This pin cannot
be left floating.
SHDN1 (Pin 12/Pin 10): Forcing this pin above 1.4V
enables the buck-boost converter. Forcing this pin below
0.4V disables the buck-boost converter. This pin cannot
be left floating.
(FE/UF Packages)
相關PDF資料
PDF描述
LTC3525DESC6-3.3#PBF 0.45 A SWITCHING REGULATOR, PDSO6
LTC3525LESC6-3TRM 0.45 A SWITCHING REGULATOR, PDSO6
LTC3525LESC6-3 0.45 A SWITCHING REGULATOR, PDSO6
LTC3526BEDC-2 0.5 A SWITCHING REGULATOR, 2400 kHz SWITCHING FREQ-MAX, PDSO6
LTC3526EDC 0.5 A SWITCHING CONTROLLER, 1300 kHz SWITCHING FREQ-MAX, PDSO6
相關代理商/技術參數
參數描述
LTC3522 制造商:LINER 制造商全稱:Linear Technology 功能描述:Synchronous 400mA Buck-Boost and 200mA Buck Converters
LTC3522EUD 制造商:LINER 制造商全稱:Linear Technology 功能描述:Synchronous 400mA Buck-Boost and 200mA Buck Converters
LTC3522EUD#PBF 功能描述:IC REG BUCK BOOST SYNC ADJ 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:MIC23xxx HyperLight Load™ Regulators 標準包裝:5,000 系列:HyperLight Load® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.8V 輸入電壓:2.7 V ~ 5.5 V PWM 型:混合物 頻率 - 開關:4MHz 電流 - 輸出:2A 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-VFDFN 裸露焊盤，8-MLF? 包裝:帶卷 (TR) 供應商設備封裝:8-MLF?（2x2） 產品目錄頁面:1094 (CN2011-ZH PDF) 其它名稱:576-3303-2
LTC3522EUD#TRPBF 功能描述:IC REG BUCK BOOST SYNC ADJ 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤
LTC3523 制造商:LINER 制造商全稱:Linear Technology 功能描述:Synchronous 600mA Step-Up and 400mA Step-Down DC/DC Converters
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*