參數資料
型號: LTC3412IFE
廠商: LINEAR TECHNOLOGY CORP
元件分類: 穩壓器
英文描述: 6.5 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO16
封裝: 4.40 MM, PLASTIC, TSSOP-16
文件頁數: 3/20頁
文件大?。?/td> 214K
代理商: LTC3412IFE
LTC3412
11
3412fb
current to remain equal to IBURST regardless of further
reductions in the load current. Since the average inductor
current is greater than the output load current, the voltage
on the ITH pin will decrease. When the ITH voltage drops to
150mV, sleep mode is enabled in which both power
MOSFETs are shut off along with most of the circuitry to
minimize power consumption. All circuitry is turned back
on and the power MOSFETs begin switching again when
the output voltage drops out of regulation. The value for
IBURST is determined by the desired amount of output
voltage ripple. As the value of IBURST increases, the sleep
period between pulses and the output voltage ripple in-
crease. The burst clamp voltage, VBURST, can be set by a
resistor divider from the VFB pin to the SGND pin as shown
in Figure 1.
Pulse skipping, which is a compromise between low out-
put voltage ripple and efficiency, can be implemented by
connecting the SYNC/MODE pin to ground. This sets IBURST
to 0A. In this condition, the peak inductor current is limited
by the minimum on-time of the current comparator, and
the lowest output voltage ripple is achieved while still op-
erating discontinuously. During very light output loads,
pulse skipping allows only a few switching cycles to be
skipped while maintaining the output voltage in regulation.
Frequency Synchronization
The LTC3412’s internal oscillator can be synchronized to
an external clock signal. During synchronization, the top
MOSFET turn-on is locked to the falling edge of the
external frequency source. The synchronization frequency
range is 300kHz to 4MHz. Synchronization only occurs if
the external frequency is greater than the frequency set by
the external resistor. Because slope compensation is
generated by the oscillator’s RC circuit, the external fre-
quency should be set 25% higher than the frequency set
by the external resistor to ensure that adequate slope
compensation is present.
Soft-Start
The RUN/SS pin provides a means to shut down the
LTC3412 as well as a timer for soft-start. Pulling the
RUN/SS pin below 0.5V places the LTC3412 in a low
quiescent current shutdown state (IQ < 1μA).
APPLICATIO S I FOR ATIO
WU
U
the power is supplied by a wall adapter through long wires,
a load step at the output can induce ringing at the input,
VIN. At best, this ringing can couple to the output and be
mistaken as loop instability. At worst, a sudden inrush of
current through the long wires can potentially cause a
voltage spike at VIN large enough to damage the part.
Output Voltage Programming
The output voltage is set by an external resistive divider
according to the following equation:
VV
R
OUT =+
08
1
2
1
.
The resistive divider allows the VFB pin to sense a fraction
of the output voltage as shown in Figure 2.
Figure 2. Setting the Output Voltage
LTC3412
VFB
VOUT
SGND
3412 F02
R2
R1
Burst Clamp Programming
If the voltage on the SYNC/MODE pin is less than VIN by 1V,
Burst Mode operation is enabled. During Burst Mode
operation, the voltage on the SYNC/MODE pin determines
the burst clamp level which sets the minimum peak
inductor current, IBURST, for each switching cycle accord-
ing to the following equation:
IV
V
A
V
BURST
=
()
02
375
08
.
VBURST is the voltage on the SYNC/MODE pin. IBURST can
be programmed in the range of 0A to 3.75A. For values of
VBURST greater than 1V, IBURST is set at 3.75A. For values
of VBURST less than 0.2V, IBURST is set at 0A. As the output
load current drops, the peak inductor current decreases to
keep the output voltage in regulation. When the output
load current demands a peak inductor current that is less
than IBURST, the burst clamp will force the peak inductor
相關PDF資料
PDF描述
LTC3427EDC#PBF 0.5 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO6
LTC3496IUFD#TRPBF SWITCHING CONTROLLER, 2300 kHz SWITCHING FREQ-MAX, PQCC28
LTC3496EUFD#PBF SWITCHING CONTROLLER, 2300 kHz SWITCHING FREQ-MAX, PQCC28
LTC3496EUFD#TRPBF SWITCHING CONTROLLER, 2300 kHz SWITCHING FREQ-MAX, PQCC28
LTC3521EFE#TRPBF SWITCHING REGULATOR, 1350 kHz SWITCHING FREQ-MAX, PDSO20
相關代理商/技術參數
參數描述
LTC3412IFE#PBF 功能描述:IC REG BUCK SYNC ADJ 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓(升壓) 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型,TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT
LTC3412IFE#TRPBF 功能描述:IC REG BUCK SYNC ADJ 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓(升壓) 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型,TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT
LTC3413 制造商:LINER 制造商全稱:Linear Technology 功能描述:3A, 2MHz Monolithic Synchronous Regulator for DDR/QDR Memory Termination
LTC3413EFE 功能描述:IC REG BUCK SYNC ADJ 3A 16TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓(升壓) 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型,TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT
LTC3413EFE#PBF 功能描述:IC REG BUCK SYNC ADJ 3A 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓(降壓) 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON(1.45x1) 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2