- 您現在的位置：買賣IC網 > PDF目錄10325 > LTC2499CUHF#TRPBF (Linear Technology)IC ADC 24BIT DELTA SIG 38-QFN PDF資料下載
參數資料
| 型號： | LTC2499CUHF#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 7/34頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 24BIT DELTA SIG 38-QFN |
| 標準包裝： | 2,500 |
| 位數： | 24 |
| 采樣率（每秒）： | 7.5 |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 480µW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 38-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 38-QFN（5x7） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 16 個單端，雙極；8 個差分，雙極 |
| 配用： | DC1012A-A-ND - BOARD DELTA SIGMA ADC LTC2499 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
LTC2499
2499fd
I2C INTERFACE
The LTC2499 communicates through an I2C interface. The
I2C interface is a 2-wire open-drain interface supporting
multiple devices and multiple masters on a single bus. The
connected devices can only pull the data line (SDA) LOW
and can never drive it HIGH. SDA is required to be exter-
nally connected to the supply through a pull-up resistor.
When the data line is not being driven, it is HIGH. Data on
the I2C bus can be transferred at rates up to 100kbits/s in
the standard mode and up to 400kbits/s in the fast mode.
The VCC power should not be removed from the device
when the I2C bus is active to avoid loading the I2C bus
lines through the internal ESD protection diodes.
Each device on the I2C bus is recognized by a unique
address stored in that device and can operate either as a
transmitter or receiver, depending on the function of the
device. In addition to transmitters and receivers, devices
canalsobeconsideredasmastersorslaveswhenperform-
ing data transfers. A master is the device which initiates a
data transfer on the bus and generates the clock signals
to permit that transfer. Devices addressed by the master
are considered a slave.
The LTC2499 can only be addressed as a slave. Once
addressed, it can receive configuration bits (channel
selection, rejection mode, speed mode) or transmit the
last conversion result. The serial clock line, SCL, is always
an input to the LTC2499 and the serial data line SDA is
bidirectional. The device supports the standard mode and
the fast mode for data transfer speeds up to 400kbits/s.
Figure 2 shows the definition of the I2C timing.
The START and STOP Conditions
A START (S) condition is generated by transitioning SDA
from HIGH to LOW while SCL is HIGH. The bus is consid-
ered to be busy after the START condition. When the data
transfer is finished, a STOP (P) condition is generated by
transitioning SDA from LOW to HIGH while SCL is HIGH.
The bus is free after a STOP is generated. START and STOP
conditions are always generated by the master.
When the bus is in use, it stays busy if a repeated START
(Sr)isgeneratedinsteadofaSTOPcondition.Therepeated
START timing is functionally identical to the START and is
used for writing and reading from the device before the
initiation of a new conversion.
Data Transferring
After the START condition, the I2C bus is busy and data
transfer can begin between the master and the addressed
slave. Data is transferred over the bus in groups of nine
bits, one byte followed by one acknowledge (ACK) bit. The
master releases the SDA line during the ninth SCL clock
cycle. The slave device can issue an ACK by pulling SDA
LOW or issue a Not Acknowledge (NACK) by leaving the
SDA line high impedance (the external pull-up resistor will
hold the line HIGH). Change of data only occurs while the
clock line (SCL) is LOW.
DATA FORMAT
After a START condition, the master sends a 7-bit address
followed by a read/write (R/W) bit. The R/W bit is 1 for a
read request and 0 for a write request. If the 7-bit address
Figure 2. Definition of Timing for Fast/Standard Mode Devices on the I2C Bus
applications inForMation
SDA
SCL
S
Sr
P
S
tHD(SDA)
tHD(DAT)
tSU(STA)
tSU(STO)
tSU(DAT)
tLOW
tHD(SDA)
tSP
tBUF
tr
tf
tr
tf
tHIGH
2499 F02
相關PDF資料 |
PDF描述 |
|---|---|
| AD7887ARZ-REEL7 | IC ADC 12BIT 2CHAN SRL 8SOIC |
| LTC2498CUHF#TRPBF | IC ADC 24BIT 16CH 38-QFN |
| D38999/26WJ61PNLC | CONN HSG PLUG 61POS STRGHT PINS |
| LTC2430IGN#TRPBF | IC ADC 20BIT DIFFINPUT/REF16SSOP |
| LTC2435-1IGN#TRPBF | IC ADC DIFF I/REF 20BIT 16-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2499IUHF#PBF | 功能描述:IC ADC 24BIT DELTA SIG 38-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2499IUHF#TRPBF | 功能描述:IC ADC 24BIT DELTA SIG 38-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2600CGN | 功能描述:IC DAC OCTAL R-R 16BIT 16SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k |
| LTC2600CGN#PBF | 功能描述:IC DAC OCTAL R-R 16BIT 16SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
| LTC2600CGN#PBF | 制造商:Linear Technology 功能描述:IC 16BIT DAC OCTAL RR 16SSOP 制造商:Linear Technology 功能描述:IC, 16BIT DAC, OCTAL, RR, 16SSOP |
發布緊急采購，3分鐘左右您將得到回復。