- 您現在的位置：買賣IC網 > PDF目錄10252 > LTC2449IUHF (Linear Technology)IC ADC 24BIT HI SPEED 38QFN PDF資料下載
參數資料
| 型號： | LTC2449IUHF |
| 廠商： | Linear Technology |
| 文件頁數： | 7/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 24BIT HI SPEED 38QFN |
| 標準包裝： | 52 |
| 位數： | 24 |
| 采樣率（每秒）： | 8k |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 40mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 38-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 38-QFN（5x7） |
| 包裝： | 管件 |
| 輸入數目和類型： | 16 個單端，雙極；8 個差分，雙極 |
| 配用： | DC742A-ND - BOARD DELTA SIGMA ADC LTC2449 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC2444/LTC2445/
LTC2448/LTC2449
15
2444589fb
Speed Multiplier Mode
In addition to selecting the speed/resolution, a speed
multiplier mode is used to double the output rate while
maintaining the selected resolution. The last bit of the 5-bit
speed/resolution control word (TWOX, see Table 5) deter-
mines if the output rate is 1X (no speed increase) or 2X
(double the selected speed).
While operating in the 1X mode, the device combines two
internal conversions for each conversion result in order to
remove the ADC offset. Every conversion cycle, the offset
and offset drift are transparently calibrated greatly simpli-
fying the user interface. The resulting conversion result
has no latency. The first conversion following a newly
selected speed/resolution and input channel is valid. This
is identical to the operation of the LTC2440, LTC2414 and
LTC2418.
While operating in the 2X mode, the device performs a
running average of the last two conversion results. This
automatically removes the offset and drift of the device
while increasing the output rate by 2X. The resolution
(noise) remains the same. If a new channel is selected, the
conversion result is valid for all conversions after the first
conversion (one cycle latency). If a new speed/resolution
is selected, the first conversion result is valid but the
resolution (noise) is a function of the running average. All
subsequent conversion results are valid. If the mode is
changed from either 1X to 2X or 2X to 1X without changing
the resolution or channel, the first conversion result is
valid.
If an external buffer/amplifier circuit is used for the
LTC2445/LTC2449, the 2X mode can be used to increase
the settling time of the amplifier between readings. While
operating in the 2X mode, the multiplexer output (input to
the external buffer/amplifier) is switched at the end of each
conversion cycle. Prior to concluding the data out/in cycle,
the analog multiplexer output is switched. This occurs at
the end of the conversion cycle (just prior to the data
output cycle) for auto calibration. The time required to
read the conversion enables more settling time for the
external buffer/amplifier. The offset/offset drift of the
external amplifier is automatically removed by the
converter’s auto calibration sequence for both the 1X and
2X speed modes.
While operating in the 1X mode, if a new input channel is
selected the multiplexer is switched on the falling edge of
the 14th SCK (once the complete data input word is
programmed). The remaining data output sequence time
can be used to allow the external buffer/amplifier to settle.
BUSY
The BUSY output (Pin 2) is used to monitor the state of
conversion, data output and sleep cycle. While the part is
converting, the BUSY pin is HIGH. Once the conversion is
complete, BUSY goes LOW indicating the conversion is
complete and data out is ready. The part now enters the
LOW power sleep state. BUSY remains LOW while data is
shifted out of the device and SDI is shifted into the device.
It goes HIGH at the conclusion of the data input/output
cycle indicating a new conversion has begun. This rising
edge may be used to flag the completion of the data read
cycle.
SERIAL INTERFACE TIMING MODES
The LTC2444/LTC2445/LTC2448/LTC2449’s 3- or 4-wire
interface is SPI and MICROWIRE compatible. This inter-
face offers several flexible modes of operation. These in-
clude internal/external serial clock, 3- or 4-wire I/O, single
cycle conversion and autostart. The following sections
describe each of these serial interface timing modes in
detail. In all these cases, the converter can use the internal
oscillator (FO = LOW) or an external oscillator connected
to the FO pin. Refer to Table 6 for a summary.
Table 6. LTC2444/LTC2445/LTC2448/LTC2449 Interface Timing Modes
Conversion
Data
Connection
SCK
Cycle
Output
and
Configuration
Source
Control
Waveforms
External SCK, Single Cycle Conversion
External
CS and SCK
Figures 4, 5
External SCK, 2-Wire I/O
External
SCK
Figure 6
Internal SCK, Single Cycle Conversion
Internal
CS
↓
CS
↓
Figures 7, 8
Internal SCK, 2-Wire I/O, Continuous Conversion
Internal
Continuous
Internal
Figure 9
APPLICATIO S I FOR ATIO
WU
UU
相關PDF資料 |
PDF描述 |
|---|---|
| MS27467T11B4SB | CONN PLUG 4POS STRAIGHT W/SCKT |
| MS27472E16F99P | CONN RCPT 23POS WALL MT W/PINS |
| LTC2448IUHF | IC ADC 24BIT HI SPEED 38QFN |
| CS3101A-10SL-55P | CONN RCPT 3POS IN LINE W/PINS |
| LTC2381CMS-16#TRPBF | IC ADC 16BIT 1CH 250KSPS 16-MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2449IUHF#PBF | 功能描述:IC ADC 24BIT HI SPEED 38QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2449IUHF#TR | 功能描述:IC ADC 24BIT HI SPEED 38QFN RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2449IUHF#TRPBF | 功能描述:IC ADC 24BIT HI SPEED 38QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2450CDC#PBF | 制造商:Linear Technology 功能描述:ADC Single Delta-Sigma 30sps 16-bit Serial 6-Pin DFN EP 制造商:Linear Technology 功能描述:ADC Single Delta-Sigma 0.03KSPS 16-Bit Serial 6-Pin DFN EP 制造商:Linear Technology 功能描述:ADC Single Delta-Sigma 0.03KSPS 16-Bit Serial 6-Pin DFN EP Bulk 制造商:Linear Technology 功能描述:ADC 16BIT 30SPS SPI DFN-6 制造商:Linear Technology 功能描述:ADC, 16BIT, 30SPS, SPI, DFN-6; Resolution (Bits):16bit; Sampling Rate:30SPS; Supply Voltage Type:Single; Supply Voltage Min:2.7V; Supply Voltage Max:5.5V; Supply Current:350A; Digital IC Case Style:DFN; No. of Pins:6 ;RoHS Compliant: Yes |
| LTC2450CDC#TRMPBF | 功能描述:IC ADC 16BIT DELTA SIG 6-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 位數:10 采樣率（每秒）:357k 數據接口:DSP，MICROWIRE?，QSPI?，串行，SPI? 轉換器數目:1 功率耗散（最大）:830µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:剪切帶 (CT) 輸入數目和類型:2 個單端，單極；2 個單端，雙極；1 個差分，單極；1 個差分，雙極 產品目錄頁面:1396 (CN2011-ZH PDF) 其它名稱:MAX1395ETB+TCT |
發布緊急采購，3分鐘左右您將得到回復。