- 您現在的位置：買賣IC網 > PDF目錄384633 > LTC2421 (Linear Technology Corporation) 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10 PDF資料下載
參數資料
| 型號： | LTC2421 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10 |
| 中文描述： | 1-/2-Channel 20位ADC的無延遲UPower采用MSOP - 10 |
| 文件頁數： | 28/32頁 |
| 文件大?。?/td> | 375K |
| 代理商： | LTC2421 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁
28
LTC2421/LTC2422
24212f
APPLICATIOU
The selection between CH0 and CH1 is automatic. Initially,
after power-up, a conversion is performed on CH0. For
each subsequent conversion, the input channel selection
is alternated. Embedded within the serial data output is a
status bit indicating which channel corresponds to the
conversion result. If the conversion was performed on
CH0, this bit (Bit 22) is LOW and is HIGH if the conversion
was performed on CH1 (see Figure 33).
There are no extra control or status pins required to per-
form the alternating 2-channel measurements. The
LTC2422 only requires two digital signals (SCK and SDO).
This simplification is ideal for isolated temperature mea-
surements or systems where minimal control signals are
available.
Pseudo Differential Applications
Generally, designers choose fully differential topologies
for several reasons. First, the interface to a 4- or 6-wire
bridge is simple (it is a differential output). Second, they
require good rejection of line frequency noise. Third, they
typically look at a small differential signal sitting on a
large common mode voltage; they need accurate
measurements of the differential signal independent of
the common mode input voltage. Many applications cur-
rently using fully differential analog-to-digital converters
for any of the above reasons may migrate to a pseudo
differential conversion using the LTC2422.
Direct Connection to a Full Bridge
The LTC2422 interfaces directly to a 4- or 6-wire bridge,
as shown in Figure 34. The LTC2422 includes a FS
SET
and
a ZS
SET
for sensing the excitation voltage directly across
the bridge. This eliminates errors due to excitation cur-
rents flowing through parasitic resistors. The LTC2422
also includes two single ended input channels which can
tie directly to the differential output of the bridge. The two
W
U
U
conversion results may be digitally subtracted yielding the
differential result.
The LTC2422’s single ended rejection of line frequencies
(
±
2%) and harmonics is better than 110dB. Since the
device performs two independent single ended conver-
sions each with >110dB rejection, the overall common
mode and differential rejection is much better than the
80dB rejection typically found in other differential input
delta-sigma converters.
In addition to excellent rejection of line frequency noise,
the LTC2422 also exhibits excellent single ended noise
rejection over a wide range of frequencies due to its 4
th
order sinc filter. Each single ended conversion indepen-
dently rejects high frequency noise (>60Hz). Care must be
taken to insure noise at frequencies below 15Hz and at
multiples of the ADC sample rate (15,360Hz) are not
present. For this application, it is recommended the
LTC2422 is placed in close proximity to the bridge sensor
in order to reduce the noise injected into the ADC input. By
performing three successive conversions (CH0-CH1-CH0),
the drift and low frequency noise can be measured and
compensated for digitally.
Figure 33. Embedded Selected Channel Indicator
24212 F33
SCK
SDO
CH1
CH1 DATA OUT
CH0 DATA OUT
EOC
CH0
EOC
Figure 34. Pseudo Differential Strain Guage Application
V
CC
LTC2422
FS
SET
ZS
SET
SCK
CH1
SDO
F
O
CS
CH0
GND
3-WIRE
SPI INTERFACE
1
5V
9
8
7
10
6
24212 F32
2
350
350
350
350
I
DC
= 0
3
4
5
I
DC
= 0
I
EXCITATION
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2422 | 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10 |
| LTUX | 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10 |
| LTUY | 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10 |
| LTUZ | 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10 |
| LTVA | 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2421CMS | 功能描述:IC ADC 1CH 20BIT MICRPWR 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2421CMS#PBF | 功能描述:IC ADC 1CH 20BIT MICRPWR 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2421CMS#TR | 功能描述:IC ADC 1CH 20BIT MICRPWR 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2421CMS#TRPBF | 功能描述:IC ADC 1CH 20BIT MICRPWR 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2421IMS | 功能描述:IC ADC 1CH 20BIT MICRPWR 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。