- 您現在的位置：買賣IC網 > PDF目錄10061 > LTC2283CUP#TRPBF (Linear Technology)IC ADC DUAL 12BIT 125MSPS 64QFN PDF資料下載
參數資料
| 型號： | LTC2283CUP#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 23/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC DUAL 12BIT 125MSPS 64QFN |
| 標準包裝： | 2,000 |
| 位數： | 12 |
| 采樣率（每秒）： | 125M |
| 數據接口： | 并聯 |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 915mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 64-QFN（9x9） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個單端，雙極; 2 個差分, 雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁
LTC2283
8
2283fb
PIN FUNCTIONS
AINA+ (Pin 1): Channel A Positive Differential Analog
Input.
AINA– (Pin 2): Channel A Negative Differential Analog
Input.
REFHA (Pins 3, 4): Channel A High Reference. Short to-
gether and bypass to Pins 5, 6 with a 0.1μF ceramic chip
capacitor as close to the pin as possible. Also bypass to
Pins 5, 6 with an additional 2.2μF ceramic chip capacitor
and to ground with a 1μF ceramic chip capacitor.
REFLA (Pins 5, 6): Channel A Low Reference. Short to-
gether and bypass to Pins 3, 4 with a 0.1μF ceramic chip
capacitor as close to the pin as possible. Also bypass to
Pins 3, 4 with an additional 2.2μF ceramic chip capacitor
and to ground with a 1μF ceramic chip capacitor.
VDD (Pins 7, 10, 18, 63): Analog 3V Supply. Bypass to
GND with 0.1μF ceramic chip capacitors.
CLKA (Pin 8): Channel A Clock Input. The input sample
starts on the positive edge.
CLKB (Pin 9): Channel B Clock Input. The input sample
starts on the positive edge.
REFLB (Pins 11, 12): Channel B Low Reference. Short
together and bypass to Pins 13, 14 with a 0.1μF ceramic
chip capacitor as close to the pin as possible. Also by-
pass to Pins 13, 14 with an additional 2.2μF ceramic
chip capacitor and to ground with a 1μF ceramic chip
capacitor.
REFHB (Pins 13, 14): Channel B High Reference. Short
together and bypass to Pins 11, 12 with a 0.1μF ceramic
chip capacitor as close to the pin as possible. Also by-
pass to Pins 11, 12 with an additional 2.2μF ceramic
chip capacitor and to ground with a 1μF ceramic chip
capacitor.
AINB– (Pin 15): Channel B Negative Differential Analog
Input.
AINB+ (Pin 16): Channel B Positive Differential Analog
Input.
GND (Pins 17, 64): ADC Power Ground.
SENSEB (Pin 19): Channel B Reference Programming Pin.
Connecting SENSEB to VCMB selects the internal reference
and a ±0.5V input range. VDD selects the internal reference
and a ±1V input range. An external reference greater than
0.5V and less than 1V applied to SENSEB selects an input
range of ±VSENSEB. ±1V is the largest valid input range.
VCMB (Pin 20): Channel B 1.5V Output and Input Common
Mode Bias. Bypass to ground with 2.2μF ceramic chip
capacitor. Do not connect to VCMA.
MUX (Pin 21): Digital Output Multiplexer Control. If MUX
is High, Channel A comes out on DA0-DA11; Channel B
comes out on DB0-DB11. If MUX is Low, the output bus-
ses are swapped and Channel A comes out on DB0-DB11;
Channel B comes out on DA0-DA11. To multiplex both
channels onto a single output bus, connect MUX, CLKA
and CLKB together. (This is not recommended at clock
frequencies above 80Msps.)
SHDNB (Pin 22): Channel B Shutdown Mode Selection
Pin. Connecting SHDNB to GND and OEB to GND results
in normal operation with the outputs enabled. Connecting
SHDNB to GND and OEB to VDD results in normal operation
with the outputs at high impedance. Connecting SHDNB
to VDD and OEB to GND results in nap mode with the
outputs at high impedance. Connecting SHDNB to VDD
and OEB to VDD results in sleep mode with the outputs
at high impedance.
OEB (Pin 23): Channel B Output Enable Pin. Refer to
SHDNB pin function.
NC (Pins 24, 25, 41, 42): Do not connect these pins.
DB0 – DB11 (Pins 26 to 30, 33 to 39): Channel B Digital
Outputs. DB11 is the MSB.
OGND (Pins 31, 50): Output Driver Ground.
OVDD (Pins 32, 49): Positive Supply for the Output Drivers.
Bypass to ground with 0.1μF ceramic chip capacitor.
CLKOUT (Pin 40): Data Ready Clock Output. Latch data
on the falling edge of CLKOUT. CLKOUT is derived from
CLKB. Tie CLKA to CLKB for simultaneous operation.
DA0 – DA11 (Pins 43 to 48, 51 to 56): Channel A Digital
Outputs. DA11 is the MSB.
OF (Pin 57): Overow/Underow Output. High when an
overow or underow has occurred on either Channel A
or Channel B.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2230IUP#PBF | IC ADC 10BIT 170MSPS 64-QFN |
| AD976AAN | IC ADC 16BIT 200KSPS 28-DIP |
| D38999/24WC8SB | CONN RCPT 8POS JAM NUT W/SCKT |
| MS27508E14F37SA | CONN RCPT 37POS BOX MNT W/SCKT |
| MS3100R28-12S | CONN RCPT 26POS WALL MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2283IUP | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual 12-Bit, 125Msps Low Power 3V ADC |
| LTC2283IUP#PBF | 功能描述:IC ADC DUAL 12BIT 125MSPS 64QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2283IUP#TRPBF | 功能描述:IC ADC DUAL 12BIT 125MSPS 64QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2283IUP-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual 12-Bit, 125Msps Low Power 3V ADC |
| LTC2283IUP-TR | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual 12-Bit, 125Msps Low Power 3V ADC |
發布緊急采購，3分鐘左右您將得到回復。