參數資料
型號： LTC1851CFW
廠商： Linear Technology
文件頁數： 15/28頁
文件大小： 0K
描述： IC ADC 12BIT 1.25MSPS 48-TSSOP
標準包裝： 39
位數： 12
采樣率（每秒）： 1.25M
數據接口： 并聯
轉換器數目： 1
功率耗散（最大）： 50mW
電壓電源： 單電源
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 48-TFSOP（0.240"，6.10mm 寬）
供應商設備封裝： 48-TSSOP
包裝： 管件
輸入數目和類型： 8 個單端，單極；8 個單端，雙極；4 個差分，單極；4 個差分，雙極
產品目錄頁面： 1347 (CN2011-ZH PDF)
22
LTC1850/LTC1851
18501f
APPLICATIO S I FOR ATIO
WU
UU
In slow memory mode, the processor applies a logic low
to RD ( = CONVST), starting the conversion. BUSY goes
low, forcing the processor into a Wait state. The previous
conversion result appears on the data outputs. When the
conversion is complete, the new conversion results ap-
pear on the data outputs; BUSY goes high releasing the
processor, and the processor takes RD ( = CONVST) back
high and reads the new conversion data.
In ROM mode, the processor takes RD ( = CONVST) low,
starting a conversion and reading the previous conversion
result. After the conversion is complete, the processor can
read the new result and initiate another conversion.
MODES OF OPERATION
Direct Address Mode
The simplest mode of operation is the Direct Address
mode. This mode is selected when both the M1 and M0
pins are low. In this mode, the address input pins directly
control the MUX and the configuration input pins directly
control the input span. The address and configuration
input pins are enabled when WR is low. WR can be tied low
if the pins will be constantly driven or the rising edge of WR
can be used to latch and hold the inputs for as long as WR
is held high.
Scan Mode
Scan mode is selected when M1 is low and M0 is high. This
mode allows the converter to scan through all of the input
channels sequentially and repeatedly without the user
having to provide an address. The address input pins (A2
to A0) are ignored but the DIFF, PGA and UNI/BIP pins are
still enabled when WR is low. As in the direct address
mode, WR can be held low or the rising edge of WR can be
used to latch and hold the information on these pins for as
long as WR is held high. The DIFF pin selects the scan
pattern. If DIFF is held low, the scan pattern will consist of
all eight channels in succession, single-ended relative to
COM (CH0-COM, CH1-COM, CH2-COM, CH3-COM,
CH4-COM, CH5-COM, CH6-COM, CH7-COM, repeat). At
the maximum conversion rate the throughput rate for each
channel would be 1.25Msps/8 or 156.25ksps. If DIFF is
held high, the scan pattern will consist of four differential
pairs (CH0-CH1, CH2-CH3, CH4-CH5, CH6-CH7, repeat).
At the maximum conversion rate, the throughput rate for
each pair would be 1.25Msps/4 or 312.5ksps. It is pos-
sible to drive the DIFF input pin while the part is in Scan
mode to achieve combinations of single-ended and differ-
ential inputs. For instance, if the A0OUT pin is tied to the
DIFF input pin, the scan pattern will consist of four single-
ended inputs and two differential pairs (CH0-COM single-
ended, CH1-COM single-ended, CH2-CH3 differential,
CH4-COM single-ended, CH5-COM single-ended, CH6-
CH7 differential, repeat).
The scan counter is reset to zero whenever the M0 pin
changes state so that the first conversion after M0 rises
will be MUX Address 000 (CH0-COM single-ended or CH0-
CH1 differential depending on the state of the DIFF pin). A
conversion is initiated by the falling edge of CONVST. After
each conversion, the address counter is advanced (by one
if DIFF is low, by two if DIFF is high) and the MUX address
for the present conversion is available on the address
output pins (DIFFOUT, A2OUT to A0OUT) along with the
conversion result.
Program/Readback Mode
The LTC1850/LTC1851 include a sequencer that can be
programmed to run a sequence of up to 16 locations
containing a MUX address and input configuration. The
MUX address and input configuration for each location are
programmed using the DIFF, A2 to A0, UNI/BIP and PGA
pins and are stored in memory along with an end-of-
sequence (EOS) bit that is generated automatically. The
six input address and configuration bits plus the EOS bit
can be read back by accessing the 7-bit readback status
word (S6-S0) through the data output pins. The sequencer
memory is a 16
× 7 block of memory represented by the
block diagram in Figure 10.
相關PDF資料
PDF描述
LTC1853IFW#TRPBF IC A/D CONV 8CH 12BIT 48-TSSOP
LTC1856IG#PBF IC ADC 16BIT 100KSPS 28-SSOP
LTC1859IG#TRPBF IC A/D CONV 8CH 16BIT 28-SSOP
LTC1867AIGN#TRPBF IC ADC 16BIT 8CH 200KSPS 16SSOP
LTC1867LCGN#PBF IC ADC 16BIT 8CH 175KSPS 16SSOP
相關代理商/技術參數
參數描述
LTC1851CFW#PBF 功能描述:IC ADC 12BIT 1.25MSPS 48-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
LTC1851CFW#TR 功能描述:IC ADC 12BIT 1.25MSPS 48-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
LTC1851CFW#TRPBF 功能描述:IC ADC 12BIT 1.25MSPS 48-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
LTC1851CFWPBF 制造商:Linear Technology 功能描述:ADC,LTC1851 12bit 1.25MSPS 8 ch TSSOP
LTC1851IFW 功能描述:IC ADC 12BIT 1.25MSPS 48-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*