- 您現在的位置：買賣IC網 > PDF目錄385505 > LTC1705EGN (LINEAR TECHNOLOGY CORP) Dual 550kHz Synchronous Switching Regulator Controller with 5-Bit VID and 150mA LDO PDF資料下載
參數資料
| 型號： | LTC1705EGN |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Dual 550kHz Synchronous Switching Regulator Controller with 5-Bit VID and 150mA LDO |
| 中文描述： | 5 A DUAL SWITCHING CONTROLLER, 650 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | 0.150 INCH, PLASTIC, SSOP-28 |
| 文件頁數： | 15/28頁 |
| 文件大?。?/td> | 326K |
| 代理商： | LTC1705EGN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC1705
15
APPLICATIU
The RUN/SS pin shuts down the LTC1705 if it falls below
0.5V (Figure 4). Between 0.5V and about 1V, the LTC1705
wakes up and the duty cycle is kept to a miminum. As the
potential at RUN/SS increases, the duty cycle increases
linearly between 1V and 2V, reaching its final value of 90%
when RUN/SS is above 2V. Somewhere before this point,
the feedback amplifier will assume control of the loop and
the output will come into regulation. When RUN/SS rises
to 1V below V
CC
, the MIN feedback comparator is enabled
and the LTC1705 is in full operation.
W
U
U
includes a trimmed 10
μ
A pull-up, enabling the user to set
the voltage at I
MAX
with a single resistor, R
IMAX
, to ground.
The LTC1705 compares the two inputs and begins limiting
the output current when the magnitude of the negative
voltage at the SW pin is greater than the voltage at I
MAX
.
When the load current increases abruptly, the voltage
feedback loop forces the duty cycle to increase rapidly and
the on-time of QB will be small momentarily. The R
DS(ON)
of QB must be low enough to ensure that the SW node is
pulled low within the QB on-time for proper current
sensing.
The current limit detector is connected to an internal gm
amplifier that pulls a current from the RUN/SS pin propor-
tional to the difference in voltage magnitudes between the
SW and I
MAX
pins. The maximum value of this current is
250
μ
A (typically). It begins to discharge the soft-start
capacitor at RUN/SS, reducing the duty cycle and control-
ling the output voltage until the current drops below the
limit. The soft-start capacitor needs to move a fair amount
before it has any effect on the duty cycle, adding a delay
until the current limit takes effect (Figure 4). This allows
the LTC1705 to experience brief overload conditions with-
out affecting the output voltage regulation. The delay also
acts as a pole in the current limit loop to enhance loop
stability. While the soft-start capacitor is being discharged,
the top MOSFET must withstand the high power dissipa-
tion due to the high current especially if the regulator is
powered by a high current supply. Larger overloads cause
the soft-start capacitor to pull down quickly, protecting the
output components from damage. The current limit gm
amplifier includes a clamp to prevent it from pulling RUN/
SS below 0.5V and shutting off the LTC1705.
Power MOSFET R
DS(ON)
varies from MOSFET to MOSFET,
limiting the accuracy obtainable from the LTC1705 current
limit loop. Additionally, ringing on the SW node due to
parasitics can add to the apparent current, causing the
loop to engage early. The LTC1705 current limit is de-
signed primarily as a disaster prevention, “no blow up”
circuit and is not useful as a precision current regulator. It
should typically be set around 50% above the maximum
expected normal output current to prevent component
tolerances from encroaching on the normal current range.
See the Current Limit Programming section for advice on
choosing a valve for R
IMAX
.
Figure 4. Soft-Start Operation in Start Up and Current Limit
0V
V
OUT
5V
4V
2V
1V
0.5V
0V
MINIMUM DUTY CYCLE
1705 F04
POWER-DOWN MODE
LTC1705 ENABLE
MIN
COMPARATOR
ENABLE
RUN/SS CONTROLS
DUTY CYCLE
COMP CONTROLS
DUTY CYCLE
START UP
NORMAL
OPERATION
CURRENT
LIMIT
Current Limit
The LTC1705 includes an onboard current limit circuit that
limits the maximum output current to a user-programmed
level. It works by sensing the voltage drop across QB
during the time that QB is on and comparing that voltage
to a user-programmed voltage at I
MAX
. Since QB looks like
a low value resistor during its on-time, the voltage drop
across it is proportional to the current flowing in it. In a
buck converter, the average current in the inductor is equal
to the output current. This current also flows through QB
during its on-time. Thus, by watching the voltage across
QB, the LTC1705 can monitor the output current.
Any time QB is on and the current flowing to the output is
reasonably large, the SW node at the drain of QB will be
somewhat negative with respect to PGND. The LTC1705
senses this voltage, inverts it and compares the sensed
voltage with a positive voltage at the I
MAX
pin. The I
MAX
pin
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1710 | Synchronous 8-Bit Up/Down Binary Counters 24-PDIP 0 to 70 |
| LTC1710C | Synchronous 8-Bit Up/Down Binary Counters 24-PDIP 0 to 70 |
| LTC1710CMS8 | Dual 16-By-4 Register Files 24-SOIC 0 to 70 |
| LTC1710CS8 | SMBus Dual Monolithic High Side Switch |
| LTC1710I | SMBus Dual Monolithic High Side Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1705EGN#PBF | 功能描述:IC PWR SUPPLY CONTROLLER 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC1705EGN#TR | 功能描述:IC PWR SUPPLY CONTROLLER 28SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC1705EGN#TRPBF | 功能描述:IC PWR SUPPLY CONTROLLER 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC1706CS8-19 | 功能描述:IC VID VOLTAGE PROGRAMMER 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC1706CS8-19#PBF | 功能描述:IC VID VOLTAGE PROGRAMMER 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。