- 您現在的位置：買賣IC網 > PDF目錄385505 > LTC1705 (Linear Technology Corporation) Dual 550kHz Synchronous Switching Regulator Controller with 5-Bit VID and 150mA LDO PDF資料下載
參數資料
| 型號： | LTC1705 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Dual 550kHz Synchronous Switching Regulator Controller with 5-Bit VID and 150mA LDO |
| 中文描述： | 雙550kHz的同步開關，5位VID和150mA LDO穩壓器控制器 |
| 文件頁數： | 26/28頁 |
| 文件大?。?/td> | 326K |
| 代理商： | LTC1705 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁
LTC1705
26
TYPICAL APPLICATIO S
Figure 11. Transient Load Generator
Most loads care only about the maximum deviation from
ideal, which occurs somewhere in the first two cycles after
the load step hits. During this time, the output capacitor
does all the work until the inductor and control loop regain
control. The initial drop (or rise if the load steps down) is
entirely controlled by the ESR of the capacitor and amounts
to most of the total voltage drop. To minimize this drop,
reduce the ESR as much as possible by choosing low ESR
capacitors and/or paralleling multiple capacitors at the
output. The capacitance value accounts for the rest of the
voltage drop until the inductor current rises. With most
output capacitors, several devices paralleled to get the
ESR down will have so much capacitance that this drop
term is negligible. Ceramic capacitors are an exception; a
small ceramic capacitor can have suitably low ESR with
relatively small values of capacitance, making this second
drop term significant.
Optimizing Loop Compensation
Loop compensation has a fundamental impact on tran-
sient recovery time, the time it takes the LTC1705 to
recover after the output voltage has dropped due to output
capacitor ESR. Optimizing loop compensation entails
maintaining the highest possible loop bandwidth while
ensuring loop stability. The feedback component selection
section describes in detail the techniques used to design
an optimized Type 3 feedback loop, appropriate for most
LTC1705 systems.
Measurement Techniques
Measuring transient response presents a challenge in two
respects: obtaining an accurate measurement and gener-
ating a suitable transient to use to test the circuit. Output
measurements should be taken with a scope probe di-
rectly across the output capacitor. Proper high frequency
probing techniques should be used. In particular, don’t
use the 6" ground lead that comes with the probe! Use an
adapter that fits on the tip of the probe and has a short
ground clip to ensure that inductance in the ground path
LTC1705
V
OUT
IRFZ44 OR
EQUIVALENT
R
LOAD
50
0V TO 10V
100Hz, 5%
DUTY CYCLE
LOCATE CLOSE TO THE OUTPUT
1705 F11
PULSE
GENERATOR
doesn’t cause a bigger spike than the transient signal
being measured. Conveniently, the typical probe tip ground
clip is spaced just right to span the leads of a typical output
capacitor.
Now that we know how to measure the signal, we need to
have something to measure. The ideal situation is to use
the actual load for the test and switch it on and off while
watching the output. If this isn’t convenient, a current step
generator is needed. This generator needs to be able to
turn on and off in nanoseconds to simulate a typical
switching logic load, so stray inductance and long clip
leads between the LTC1705 and the transient generator
must be minimized.
Figure 11 shows an example of a simple transient genera-
tor. Be sure to use a noninductive resistor as the load
element—many power resistors use an inductive spiral
pattern and are not suitable for use here. A simple solution
is to take ten 1/4W film resistors and wire them in parallel
to get the desired value. This gives a noninductive resistive
load which can dissipate 2.5W continuously or 50W if
pulsed with a 5% duty cycle, enough for most LTC1705
circuits. Solder the MOSFET and the resistor(s) as close to
the output of the LTC1705 circuit as possible and set up
the signal generator to pulse at a 100Hz rate with a 5% duty
cycle. This pulses the LTC1705 with 500
μ
s transients10ms
apart, adequate for viewing the entire transient recovery
time for both positive and negative transitions while keep-
ing the load resistor cool.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1705EGN | Dual 550kHz Synchronous Switching Regulator Controller with 5-Bit VID and 150mA LDO |
| LTC1710 | Synchronous 8-Bit Up/Down Binary Counters 24-PDIP 0 to 70 |
| LTC1710C | Synchronous 8-Bit Up/Down Binary Counters 24-PDIP 0 to 70 |
| LTC1710CMS8 | Dual 16-By-4 Register Files 24-SOIC 0 to 70 |
| LTC1710CS8 | SMBus Dual Monolithic High Side Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1705EGN | 功能描述:IC PWR SUPPLY CONTROLLER 28SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC1705EGN#PBF | 功能描述:IC PWR SUPPLY CONTROLLER 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC1705EGN#TR | 功能描述:IC PWR SUPPLY CONTROLLER 28SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC1705EGN#TRPBF | 功能描述:IC PWR SUPPLY CONTROLLER 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC1706CS8-19 | 功能描述:IC VID VOLTAGE PROGRAMMER 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。