- 您現在的位置：買賣IC網 > PDF目錄385505 > LTC1703CG (LINEAR TECHNOLOGY CORP) Synchronous 8-Bit Up/Down Binary Counters 24-PDIP 0 to 70 PDF資料下載
參數資料
| 型號： | LTC1703CG |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Synchronous 8-Bit Up/Down Binary Counters 24-PDIP 0 to 70 |
| 中文描述： | 5 A DUAL SWITCHING CONTROLLER, 750 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | 0.209 INCH, PLASTIC, SSOP-28 |
| 文件頁數： | 13/36頁 |
| 文件大?。?/td> | 343K |
| 代理商： | LTC1703CG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
13
LTC1703
is limited to 10%. The maximum duty cycle limit increases
linearly between 1V and 2.5V, reaching its final value of
90% when RUN/SS is above 2.5V. Somewhere before this
point, the feedback amplifier will assume control of the
loop and the output will come into regulation. When RUN/
SS rises to 0.5V below V
CC
, the MIN feedback comparator
is enabled, and the LTC1703 is in full operation.
CURRENT LIMIT
The LTC1703 includes an onboard current limit circuit that
limits the maximum output current to a user-programmed
level. It works by sensing the voltage drop across QB
during the time that QB is on and comparing that voltage
to a user-programmed voltage at I
MAX
. Since QB looks like
a low value resistor during its on-time, the voltage drop
across it is proportional to the current flowing in it. In a
buck converter, the average current in the inductor is equal
to the output current. This current also flows through QB
during its on-time. Thus, by watching the voltage across
QB, the LTC1703 can monitor the output current.
Any time QB is on and the current flowing to the output is
reasonably large, the SW node at the drain of QB will be
somewhat negative with respect to PGND. The LTC1703
senses this voltage and inverts it to allow it to compare the
sensed voltage with a positive voltage at the I
MAX
pin. The
I
MAX
pin includes a trimmed 10
μ
A pull-up, enabling the
user to set the voltage at I
MAX
with a single resistor, R
IMAX
,
to ground. The LTC1703 compares the two inputs and
begins limiting the output current when the magnitude of
the negative voltage at the SW pin is greater than the
voltage at I
MAX
.
The current limit detector is connected to an internal g
m
amplifier that pulls a current from the RUN/SS pin propor-
tional to the difference in voltage magnitudes between the
SW and I
MAX
pins. This current begins to discharge the
soft-start capacitor at RUN/SS, reducing the duty cycle
and controlling the output voltage until the output current
drops below the limit. The soft-start capacitor needs to
move a fair amount before it has any effect on the duty
cycle, adding a delay until the current limit takes effect
(Figure 4). This allows the LTC1703 to experience brief
overload conditions without affecting the output voltage
regulation. The delay also acts as a pole in the current limit
loop to enhance loop stability. Larger overloads cause the
soft-start capacitor to pull down quickly, protecting the
output components from damage. The current limit g
m
amplifier includes a clamp to prevent it from pulling RUN/
SS below 0.5V and shutting off the device.
Power MOSFET R
DS(ON)
varies from MOSFET to MOSFET,
limiting the accuracy obtainable from the LTC1703 current
limit loop. Additionally, ringing on the SW node due to
parasitics can add to the apparent current, causing the
loop to engage early. The LTC1703 current limit is
designed primarily as a disaster prevention, “no blow up”
circuit, and is not useful as a precision current regulator.
It should typically be set around 50% above the maximum
expected normal output current to prevent component
tolerances from encroaching on the normal current range.
See the Current Limit Programming section for advice on
choosing a value for R
IMAX
.
DISCONTINUOUS/Burst Mode OPERATION
Theory of operation
The LTC1703 switching logic has three modes of opera-
tion. Under heavy loads, it operates as a fully synchro-
nous, continuous conduction switching regulator. In this
mode of operation (“continuous” mode), the current in the
inductor flows in the positive direction (toward the output)
during the entire switching cycle, constantly supplying
current to the load. In this mode, the synchronous switch
(QB) is on whenever QT is off, so the current always flows
through a low impedance switch, minimizing voltage drop
and power loss. This is the most efficient mode of opera-
tion at heavy loads, where the resistive losses in the power
devices are the dominant loss term.
Continuous mode works efficiently when the load current
is greater than half of the ripple current in the inductor. In
a buck converter like the LTC1703, the average current in
the inductor (averaged over one switching cycle) is equal
to the load current. The ripple current is the difference
between the maximum and the minimum current during a
switching cycle (see Figure 5a). The ripple current
depends on inductor value, clock frequency and output
voltage, but is constant regardless of load as long as the
APPLICATIOU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1704 | Synchronous 8-Bit Up/Down Binary Counters 24-SOIC 0 to 70 |
| LTC1704B | Synchronous 8-Bit Up/Down Binary Counters 24-SOIC 0 to 70 |
| LTC1705 | Dual 550kHz Synchronous Switching Regulator Controller with 5-Bit VID and 150mA LDO |
| LTC1705EGN | Dual 550kHz Synchronous Switching Regulator Controller with 5-Bit VID and 150mA LDO |
| LTC1710 | Synchronous 8-Bit Up/Down Binary Counters 24-PDIP 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1703CG#PBF | 功能描述:IC REG SW DUAL SYNC VID 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:2,000 系列:- 應用:控制器，DSP 輸入電壓:4.5 V ~ 25 V 輸出數:2 輸出電壓:最低可調至 1.2V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:30-TFSOP（0.173"，4.40mm 寬） 供應商設備封裝:30-TSSOP 包裝:帶卷 (TR) |
| LTC1703CG#TR | 制造商:Linear Technology 功能描述:LDO Cntrlr REG CTRLR 0.9V to 2V 28-Pin SSOP T/R |
| LTC1703CG#TRPBF | 功能描述:IC REG SW DUAL SYNC VID 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| LTC1703IG | 功能描述:IC REG SW DL SYNC W/VID 28-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| LTC1703IG#PBF | 功能描述:IC REG SW DUAL SYNC VID 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。