- 您現在的位置：買賣IC網 > PDF目錄385505 > LTC1569-7 (Linear Technology Corporation) Linear Phase, DC Accurate, Tunable, 10th Order Lowpass Filter(線性脈沖，直流精度，可調諧的10階低通濾波器) PDF資料下載
參數資料
| 型號： | LTC1569-7 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Linear Phase, DC Accurate, Tunable, 10th Order Lowpass Filter(線性脈沖，直流精度，可調諧的10階低通濾波器) |
| 中文描述： | 線性相位，直流準確，可調諧，第10階低通濾波器（線性脈沖，直流精度，可調諧的10階低通濾波器） |
| 文件頁數： | 5/12頁 |
| 文件大小： | 227K |
| 代理商： | LTC1569-7 |
5
LTC1569-7
PI
FU
CTIO
N
S
U
U
IN
+
/IN
–
(Pins 1, 2):
Signals can be applied to either or
both input pins. The DC gain from IN
+
(Pin 1) to OUT
(Pin8) is 1.0, and the DC gain from Pin 2 to Pin 8 is –1. The
input range, input resistance and output range are de-
scribed in the Applications Information section. Input
voltages which exceed the power supply voltages should
be avoided. Transients will not cause latchup if the current
into/out of the input pins is limited to 20mA.
GND (Pin 3):
The GND pin is the reference voltage for the
filter and should be externally biased to 2V (1.11V) to
maximize the dynamic range of the filter in applications
using a single 5V (3V) supply. For single supply operation,
the GND pin should be bypassed with a quality 1
μ
F
ceramic capacitor to V
–
(Pin 4). The impedance of the
circuit biasing the GND pin should be less than 2k
as the
GND pin generates a small amount of AC and DC current.
For dual supply operation, connect Pin3 to a high quality
DC ground. A ground plane should be used. A poor ground
will increase DC offset, clock feedthrough, noise and
distortion.
V
–
/V
+
(Pins 4, 7):
For 3V, 5V and
±
5V applications a
quality 1
μ
F ceramic bypass capacitor is required from V
+
(Pin 7) to V
–
(Pin 4) to provide the transient energy for the
internal clock drivers. The bypass should be as close as
possible to the IC. In dual supply applications (Pin 3 is
grounded), an additional 0.1
μ
F bypass from V
+
(Pin 7) to
GND (Pin 3) and V
–
(Pin 4) to GND (Pin 3) is recom-
mended.
The maximum voltage difference between GND (Pin 3) and
V
+
(Pin 7) should not exceed 5.5V.
DIV/CLK (Pin 5):
DIV/CLK serves two functions. When the
internal oscillator is enabled, DIV/CLK can be used to
engage an internal divider. The internal divider is set to 1:1
when DIV/CLK is shorted to V
–
(Pin 4). The internal divider
is set to 4:1 when DIV/CLK is allowed to float (a 100pF
bypass to V
–
is recommended). The internal divider is set
to 16:1 when DIV/CLK is shorted to V
+
(Pin 7). In the
divide-by-4 and divide-by-16 modes the power supply
current is reduced by typically 60%.
When the internal oscillator is disabled (R
X
shorted
to V
–
) DIV/CLK becomes an input pin for applying an
external clock signal. For proper filter operation, the clock
waveform should be a squarewave with a duty cycle as
close as possible to 50% and CMOS voltages levels (see
Electrical Characteristics section for voltage levels). DIV/
CLK pin voltages which exceed the power supply voltages
should be avoided. Transients will not cause latchup if the
fault current into/out of the DIV/CLK pin is limited to 40mA.
R
X
(Pin 6):
Connecting an external resistor between the R
X
pin and V
+
(Pin 7) enables the internal oscillator. The value
of the resistor determines the frequency of oscillation. The
maximum recommended resistor value is 40k and the
minimum is 3.8k/8k (single 5V/3V supply). The internal
oscillator is disabled by shorting the R
X
pin to V
–
(Pin 4).
(Please refer to the Applications Information section.)
OUT (Pin 8):
Filter Output. This pin can drive 10k
and/or
40pF loads. For larger capacitive loads, an external 100
series resistor is recommended. The output pin can ex-
ceed the power supply voltages by up to
±
2V without
latchup.
BLOCK DIAGRA
10TH ORDER
LINEAR PHASE
FILTER NETWORK
POWER
CONTROL
DIVIDER/
BUFFER
R
EXT
PRECISION
OSCILLATOR
5
6
7
8
4
3
2
1
OUT
V
+
R
X
DIV/CLK
IN
+
IN
–
GND
V
–
1569-7 BD
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1623 | SMBus Dual High Side Switch Controller(SMBus 雙高邊開關穩壓器) |
| LTC1654 | Dual 14-Bit Rail-to-Rail DAC in 16-Lead SSOP Package(雙路14位,滿幅度電壓輸出數模轉換器(16腳SSOP封裝)) |
| LTC1655 | 16-Bit Rail-to-Rail Micropower DACs in SO-8 Package(16位,微功耗滿幅度電壓輸出數模轉換器(SO-8封裝,內部基準2.048V)) |
| LTC1655L | 16-Bit Rail-to-Rail Micropower DACs in SO-8 Package(16位,微功耗滿幅度電壓輸出數模轉換器(SO-8封裝,內部基準1.25V)) |
| LTC1657 | Parallel 16-Bit Rail-to-Rail Micropower DAC(并行16位,微功耗滿幅度電壓輸出數模轉換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1569CS8-6 | 功能描述:IC FILTER 10TH ORDR LOWPASS8SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
| LTC1569CS8-6#PBF | 功能描述:IC FILTER 10TH ORDR LOWPASS8SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
| LTC1569CS8-6#PBF | 制造商:Linear Technology 功能描述:IC FILTER LOW PASS 64KHZ 8-SOIC 制造商:Linear Technology 功能描述:IC, FILTER, LOW PASS, 64KHZ, 8-SOIC |
| LTC1569CS8-6#TR | 功能描述:IC FILTER LP 10TH ORD LIN 8SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
| LTC1569CS8-6#TRPBF | 功能描述:IC FILTER 10TH ORDR LOWPASS8SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。