- 您現在的位置：買賣IC網 > PDF目錄385503 > LTC1412C (Linear Technology Corporation) 12-Bit, 3Msps, Sampling A/D Converter PDF資料下載
參數資料
| 型號： | LTC1412C |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 12-Bit, 3Msps, Sampling A/D Converter |
| 中文描述： | 12位，3Msps，采樣A / D轉換器 |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 499K |
| 代理商： | LTC1412C |
10
LTC1412
APPLICATIO
S I
FOR
ATIO
U
quencies above the converter’s Nyquist Frequency. The
noise floor stays very low at high frequencies; S/(N + D)
becomes dominated by distortion at frequencies far
beyond Nyquist.
W
U
U
Driving the Analog Input
The differential analog inputs of the LTC1412 are easy to
drive. The inputs may be driven differentially or as a single-
ended input (i.e., the A
IN–
input is grounded). The A
IN+
and
A
IN–
inputs are sampled at the same instant. Any unwanted
signal that is common mode to both inputs will be reduced
by the common mode rejection of the sample-and-hold
circuit. The inputs draw only one small current spike while
charging the sample-and-hold capacitors at the end of
conversion. During conversion, the analog inputs draw
only a small leakage current. If the source impedance of
the driving circuit is low then the LTC1412 inputs can be
driven directly. As source impedance increases so will
acquisition time (see Figure 6). For minimum acquisition
time, with high source impedance, a buffer amplifier must
be used. The only requirement is that the amplifier driving
the analog input(s) must settle after the small current
spike before the next conversion starts (settling time must
be 50ns for full throughput rate).
frequency. For example, if an amplifier is used in a gain of
1 and has a unity-gain bandwidth of 50MHz, then the
output impedance at 50MHz should be less than 100
.
The second requirement is that the closed-loop bandwidth
must be greater than 40MHz to ensure adequate small-
signal settling for full throughput rate. If slower op amps
are used, more settling time can be provided by increasing
the time between conversions.
The best choice for an op amp to drive the LTC1412 will
depend on the application. Generally applications fall into
two categories: AC applications where dynamic specifica-
tions are most critical and time domain applications where
DC accuracy and settling time are most critical. The
following list is a summary of the op amps that are suitable
for driving the LTC1412. More detailed information is
available in the Linear Technology Databooks and on the
LinearView
TM
CD-ROM.
LT
1223:
100MHz Video Current Feedback Amplifier.
6mA supply current.
±
5V to
±
15V supplies. Low Noise.
Good for AC applications.
LT1227:
140MHz Video Current Feedback Amplifier. 10mA
supply current.
±
5V to
±
15V supplies. Low Noise. Best for
AC applications.
LT1229/LT1230:
Dual and Quad 100MHz Current Feed-
back Amplifiers.
±
2V to
±
15V supplies. Low Noise. Good
AC specifications, 6mA supply current each amplifier.
LT1360:
50MHz Voltage Feedback Amplifier. 3.8mA sup-
ply current.
±
5V to
±
15V supplies. Good AC and DC
specifications. 70ns settling to 0.5LSB.
LT1363:
70MHz, 1000V/
μ
s Op Amps. 6.3mA supply cur-
rent. Good AC and DC specifications. 60ns settling to
0.5LSB.
LT1364/LT1365:
Dual and Quad 70MHz, 1000V/
μ
s Op
Amps. 6.3mA supply current per amplifier. 60ns settling
to 0.5LSB.
Input Filtering
The noise and the distortion of the input amplifier and
other circuitry must be considered since they will add to
the LTC1412 noise and distortion. The small-signal band-
SOURCE RESISTANCE (
)
10
0.01
A
μ
s
0.1
1
10
100
1k
1412 F06
10k
100k
Figure 6. Acquisition Time vs Source Resistance
Choosing an Input Amplifier
Choosing an input amplifier is easy if a few requirements
are taken into consideration. First, to limit the magnitude
of the voltage spike seen by the amplifier from charging
the sampling capacitor, choose an amplifier that has a low
output impedance (<100
) at the closed-loop bandwidth
LinearView is a trademark of Linear Technology Corporation.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1412CG | 12-Bit, 3Msps, Sampling A/D Converter |
| LTC1412I | 12-Bit, 3Msps, Sampling A/D Converter |
| LTC1412IG | 12-Bit, 3Msps, Sampling A/D Converter |
| LTC1414 | 14-Bit, 2.2Msps, Sampling A/D Converter |
| LTC1414CGN | Dual, Low Voltage, LinCMOS(TM) Differential Comparator 8-SOIC 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1412CG | 功能描述:IC A/D CONV 12BIT SAMPLNG 28SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC1412CG#PBF | 功能描述:IC A/D CONV 12BIT SAMPLNG 28SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC1412CG#TR | 功能描述:IC ADC 12BIT 3MSPS SAMPLE 28SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC1412CG#TRPBF | 功能描述:IC A/D CONV 12BIT SAMPLNG 28SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC1412IG | 功能描述:IC A/D CONV 12BIT SAMPLNG 28SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。