- 您現在的位置：買賣IC網 > PDF目錄385502 > LTC1148HVIS-5 (LINEAR TECHNOLOGY CORP) RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS PDF資料下載
參數資料
| 型號： | LTC1148HVIS-5 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 中文描述： | SWITCHING CONTROLLER, 250 kHz SWITCHING FREQ-MAX, PDSO14 |
| 封裝： | 0.150 INCH, PLASTIC, SOP-14 |
| 文件頁數： | 8/20頁 |
| 文件大?。?/td> | 250K |
| 代理商： | LTC1148HVIS-5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
8
LTC1148
LTC1148-3.3/LTC1148-5
114835fd
APPLICATIU
The basic LTC1148 series application circuit (fixed
output versions) is shown in Figure 1. External compo-
nent selection is driven by the load requirement, and
begins with the selection of R
SENSE
. Once R
SENSE
is
known, C
T
and L can be chosen. Next, the power
MOSFETs and D1 are selected. Finally, C
IN
and C
OUT
are
selected and the loop is compensated. The circuit
shown in Figure 1 can be configured for operation up to
an input voltage of 20V. If the application requires
higher input voltage, then the LTC1149 or LTC1159
should be used.
W
U
U
R
SENSE
Selection for Output Current
R
SENSE
is chosen based on the required output current.
The LTC1148 series current comparator has a threshold
range which extends from a minimum of 25mV/R
SENSE
to
a maximum of 150mV/R
SENSE
. The current comparator
threshold sets the peak of the inductor ripple current,
yielding a maximum output current I
MAX
equal to the peak
value less half the peak-to-peak ripple current. For proper
Burst Mode
operation, I
RIPPLE(P-P)
must be less than or
equal to the minimum current comparator threshold.
Since efficiency generally increases with ripple current,
the maximum allowable ripple current is assumed, i.e.,
I
RIPPLE(P-P)
= 25mV/R
SENSE
(See C
T
and L Selection for
Operating Frequency). Solving for R
SENSE
and allowing
a margin for variations in the LTC1148 series and
external component values yields:
R
SENSE
= 100mV
I
MAX
A graph for selecting R
SENSE
versus maximum output
current is given in Figure 2.
The load current below which Burst Mode
operation com-
mences (I
BURST
) and the peak short-circuit current (I
SC(PK)
)
both track I
MAX
. Once R
SENSE
has been chosen, I
BURST
and
I
SC(PK)
can be predicted from the following:
I
BURST
≈
15mV
R
SENSE
I
SC(PK)
= 150mV
R
SENSE
Figure 2. Selecting R
SENSE
MAXIMUM OUTPUT CURRENT (A)
0
R
S
)
0.15
0.20
4
LTC1148 F02
0.10
0.05
0
1
2
3
5
The LTC1148 series automatically extends t
OFF
during a
short circuit to allow sufficient time for the inductor
current to decay between switch cycles. The resulting
ripple current causes the average short-circuit current
I
SC(AVG)
to be reduced to approximately I
MAX
.
L and C
T
Selection for Operating Frequency
The LTC1148 series uses a constant off-time architecture
with t
OFF
determined by an external timing capacitor C
T
.
Each time the P-channel MOSFET switch turns on, the
voltage on C
T
is reset to approximately 3.3V. During the off
time, C
T
is discharged by a current which is proportional
to V
OUT
. The voltage on C
T
is analogous to the current in
inductor L, which likewise decays at a rate proportional to
V
OUT
. Thus the inductor value must track the timing
capacitor value.
The value of C
T
is calculated from the desired continuous
mode operating frequency, f:
1
2.6(10
4
)f
C
T
=
Assumes V
IN
= 2V
OUT
, Figure 1 circuit.
A graph for selecting C
T
versus frequency including the
effects of input voltage is given in Figure 3.
As the operating frequency is increased the gate charge
losses will be higher, reducing efficiency (see Efficiency
Considerations). The complete expression for operating
frequency of the circuit in Figure 1 is given by:
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1151CSW | Dual 【15V Zero-Drift Operational Amplifier |
| LTC1151 | Dual ±15V Zero-Drift Operational Amplifier(±15V，雙路，零漂移運算放大器) |
| LTC1153 | Auto-Reset Electronic Circuit Breaker |
| LTC1153C | Auto-Reset Electronic Circuit Breaker |
| LTC1153CN8 | Octal Bus Transceivers With 3-State Outputs 20-SOIC 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1148HVIS-5#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 14-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC1148HVIS-5#TR | 功能描述:IC REG CTRLR BUCK PWM CM 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC1148HVIS-5#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 14-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC1148L | 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Efficiency Synchronous Step-Down Switching Regulators |
| LTC1148LCS | 功能描述:IC REG CTRLR BUCK PWM CM 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
發布緊急采購，3分鐘左右您將得到回復。