- 您現在的位置：買賣IC網 > PDF目錄98002 > LTC1147LCS8#TR (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, 400 kHz SWITCHING FREQ-MAX, PDSO8 PDF資料下載
參數資料
| 型號： | LTC1147LCS8#TR |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, 400 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | 0.150 INCH, PLASTIC, SO-8 |
| 文件頁數： | 3/16頁 |
| 文件大?。?/td> | 217K |
| 代理商： | LTC1147LCS8#TR |
11
LTC1147-3.3
LTC1147-5/LTC1147L
sn1147 1147fds
where L1, L2, etc., are the individual losses as a percent-
age of input power. (For high efficiency circuits only small
errors are incurred by expressing losses as a percentage
of output power.)
Although all dissipative elements in the circuit produce
losses, four main sources usually account for most of the
losses in LTC1147 circuits: 1) LTC1147 DC bias current,
2) MOSFET gate charge current, 3) I
2R losses, and 4)
voltage drop of the Schottky diode.
1. The DC supply current is the current which flows into
VIN (Pin 1) less the gate charge current. For VIN = 10V
the LTC1147 series DC supply current is 160
A for no
load, and increases proportionally with load up to a
constant 1.6mA after the LTC1147 series has entered
continuous mode. Because the DC bias current is
drawn from VIN, the resulting loss increases with
input voltage. For VIN = 10V the DC bias losses are
generally less than 1% for load currents over 30mA.
However, at very low load currents the DC bias current
accounts for nearly all of the loss.
2. MOSFET gate charge current results from switching
the gate capacitance of the power MOSFET. Each time
a MOSFET gate is switched from low to high to low
again, a packet of charge dQ moves from VIN to
ground. The resulting dQ/dt is a current out of VIN
which is typically much larger than the DC supply
current. In continuous mode, IGATECHG = f(QP). The
typical gate charge for a 0.135
P-channel power
MOSFET is 40nC. This results in IGATECHG = 4mA in
100kHz continuous operation for a 2% to 3% typical
midcurrent loss with VIN = 10V.
Note that the gate charge loss increases directly with
both input voltage and operating frequency. This is the
principal reason why the highest efficiency circuits
operate at moderate frequencies. Furthermore, it ar-
gues against using a larger MOSFET than necessary to
control I
2R losses, since overkill can cost efficiency as
well as money!
3. I
2R losses are easily predicted from the DC resis-
tances of the MOSFET, inductor and current shunt. In
continuous mode the average output current flows
through L and RSENSE, but is “chopped” between the
P-channel and Schottky diode. The MOSFET RDS(ON)
multiplied by the P-channel duty cycle can be summed
with the resistances of L and RSENSE to obtain I2R
losses. For example, if RDS(ON) = 0.1, RL = 0.15,
and RSENSE = 0.05, then the total resistance is 0.3
at VIN ≈ 2VOUT. This results in losses ranging from 3%
to 10% as the output current increases from 0.5A to
2A. I2R losses cause the efficiency to roll off at high
output currents.
4. The Schottky diode is a major source of power loss at
high currents and gets worse at high input voltages.
The diode loss is calculated by multiplying the forward
voltage drop times the Schottky diode duty cycle
multiplied by the load current. For example, assuming
a duty cycle of 50% with a Schottky diode forward
voltage drop of 0.4V, the loss increases from 0.5% to
8% as the load current increases from 0.5A to 2A.
Figure 5 shows how the efficiency losses in a typical
LTC1147 series regulator end up being apportioned.
The gate charge loss is responsible for the majority of
the efficiency lost in the midcurrent region. If Burst
Mode operation was not employed at low currents,
the gate charge loss alone would cause efficiency to
drop to unacceptable levels. With Burst Mode opera-
tion, the DC supply current represents the lone (and
unavoidable) loss component which continues to
become a higher percentage as output current is
reduced. As expected, the I2R losses and Schottky
diode loss dominate at high load currents.
Figure 5. Efficiency Loss
OUTPUT CURRENT (A)
0.01
EFFICIENCY/LOSS
(%)
90
95
1
LTC1147 F05
85
80
0.03
0.1
0.3
3
100
GATE CHARGE
LTC1147 IQ
I2R
SCHOTTKY
DIODE
APPLICATIO S I FOR ATIO
WU
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1147CS8-5#TR | SWITCHING CONTROLLER, 400 kHz SWITCHING FREQ-MAX, PDSO8 |
| LTC1261CS84.5 | SWITCHED CAPACITOR REGULATOR, 550 kHz SWITCHING FREQ-MAX, PDSO8 |
| LTC1433GN | 1.2 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO16 |
| LTC1436AIGN#PBF | 2 A SWITCHING CONTROLLER, 400 kHz SWITCHING FREQ-MAX, PDSO24 |
| LTC1552CG | SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1147LIS8 | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC1147LIS8#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC1147LIS8#TR | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC1147LIS8#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC1148 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Efficiency Synchronous Step-Down Switching Regulators |
發布緊急采購，3分鐘左右您將得到回復。