- 您現在的位置：買賣IC網 > PDF目錄44987 > LT4250HCN8#TRPBF (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8 PDF資料下載
參數資料
| 型號： | LT4250HCN8#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8 |
| 封裝： | 0.300 INCH, LEAD FREE, PLASTIC, DIP-8 |
| 文件頁數： | 10/14頁 |
| 文件大?。?/td> | 232K |
| 代理商： | LT4250HCN8#TRPBF |
LT4250L/LT4250H
5
4250lhfa
PIN FUNCTIONS
for this pin is 1.5μs. Add an external capacitor to this pin
for additional filtering.
VEE (Pin 4): Negative Supply Voltage Input. Connect to
the lower potential of the power supply.
SENSE (Pin 5): Circuit Breaker Sense Pin. With a sense
resistor placed in the supply path between VEE and SENSE,
the overcurrent condition will pull down the GATE pin and
regulate the voltage across the resistor to be 50mV. If
the overcurrent condition exists for more than 500μs the
electronic circuit breaker will trip and turnoff the external
MOSFET.
If the current limit value is set to twice the normal operating
current, only 25mV is dropped across the sense resistor
during normal operation. To disable the current limit feature,
VEE and SENSE can be shorted together.
GATE (Pin 6): Gate Drive Output for the External N-channel
MOSFET. The GATE pin will go high when the following
start-up conditions are met: the UV pin is high, the OV pin
is low, (VSENSE – VEE) < 50mV and the VDD pin is greater
than VUVLOH. The GATE pin is pulled high by a 45μA cur-
rent source and pulled low with a 50mA current source.
During current limit the GATE pin is pulled low using a
100mA current source.
DRAIN (Pin 7): Analog Drain Sense Input. Connect this
pin to the drain of the external N-channel MOSFET and
the V– pin of the power module. When the DRAIN pin is
below VDL, the PWRGD/PWRGD pin will latch to indicate
the switch is on.
VDD (Pin 8): Positive Supply Voltage Input. Connect this
pin to the higher potential of the power supply inputs and
the V+ pin of the power module. An undervoltage lockout
circuit disables the chip until the VDD pin is greater than
the 16V VUVLOH threshold.
PWRGD/PWRGD (Pin 1): Power Good Output Pin. This pin
will latch a power good indication when VDRAIN is within
VDL of VEE and VGATE is within VGH of ΔVGATE. This pin
can be connected directly to the enable pin of a power
module.
When the DRAIN pin of the LT4250L is above VEE by more
than VDL or VGATE is more than VGH from ΔVGATE, the
PWRGD pin will be high impedance, allowing the pull-up
current of the module’s enable pin to pull the pin high and
turn the module off. When VDRAIN drops below VDL and
VGATE rises above VGH, the PWRGD pin sinks current to
VEE, pulling the enable pin low and turning on the module.
This condition is latched until the GATE pin is turned off
via the UV, OV, UVLO or the electronic circuit breaker.
When the DRAIN pin of the LT4250H is above VEE by more
than VDL or VGATE is more than VGH from ΔVGATE, the
PWRGD pin will sink current to the DRAIN pin which pulls
the module’s enable pin low, forcing it off. When VDRAIN
drops below VDL and VGATE rises above VGH, the PWRGD
sink current is turned off, allowing the module’s pull-up
current to pull the enable pin high and turn on the module.
This condition is latched until the GATE pin is turned off
via the UV, OV, UVLO or the electronic circuit breaker.
OV (Pin 2): Analog Overvoltage Input. When OV is pulled
above the 1.255V threshold, an overvoltage condition is
detected and the GATE pin will be immediately pulled low.
The GATE pin will remain low until OV drops below the
1.235V threshold.
UV (Pin 3): Analog Undervoltage Input. When UV is pulled
below the 1.125V threshold, an undervoltage condition
is detected and the GATE pin will be immediately pulled
low. The GATE pin will remain low until UV rises above
the 1.255 threshold.
The UV pin is also used to reset the electronic circuit
breaker. If the UV pin is cycled low and high following the
trip of the circuit breaker, the circuit breaker is reset and a
normal power-up sequence will occur. The response time
相關PDF資料 |
PDF描述 |
|---|---|
| LT4356CS-3 | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| LT4356IMS-3 | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| LT4356HMS-3#PBF | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| LT4356IS-3 | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| LT4356HMS-3 | SPECIALTY ANALOG CIRCUIT, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT4250HCS8 | 功能描述:IC CONTRLR HOTSWAP NEG 48V 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LT4250HCS8#PBF | 功能描述:IC CONTRLR HOTSWAP NEG 48V 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LT4250HCS8#TR | 功能描述:IC CONTRLR HOTSWAP NEG 48V 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LT4250HCS8#TRPBF | 功能描述:IC CONTRLR HOTSWAP NEG 48V 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LT4250HIN8 | 功能描述:IC CONTRLR HOT SWAP NEG 48V 8DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。