- 您現在的位置：買賣IC網 > PDF目錄44986 > LT3741IFE#TRPBF (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, 1070 kHz SWITCHING FREQ-MAX, PDSO20 PDF資料下載
參數資料
| 型號： | LT3741IFE#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, 1070 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封裝： | 4.40 MM, LEAD FREE, PLASTIC, TSSOP-20 |
| 文件頁數： | 2/24頁 |
| 文件大小： | 243K |
| 代理商： | LT3741IFE#TRPBF |
LT3741
10
3741fb
PIN FUNCTIONS (QFN/TSSOP)
EN/UVLO (Pin 1/Pin 4): Enable Pin. The EN/UVLO pin
acts as an enable pin and turns on the internal current
bias core and subregulators at 1.55V. The pin does
not have any pull-up or pull-down, requiring a voltage
bias for normal part operation. Full shutdown occurs at
approximately 0.5V.
VREF (Pin 2/Pin 5): Buffered 2V reference capable of
0.5mA drive.
CTRL2 (Pin 3/Pin 6): Thermal control input used to reduce
the regulated current level.
GND (Pins 4,11,14, Exposed Pad Pin 21/Pins 2,7,16,
Exposed Pad Pin 21): Ground. The exposed pad must be
soldered to the PCB
CTRL1 (Pin 5/Pin 8): The CTRL1 pin sets the high level
regulated output current and overcurrent. The maximum
input voltage is internally clamped to 1.5V. The overcurrent
set point is equal to the high level regulated current level set
by the CTRL1 pin with an additional 23mV offset between
the SENSE+ and SENSE– pins.
SS (Pin 6/Pin 9): The Soft-Start Pin. Place an external
capacitor to ground to limit the regulated current during
start-up conditions. The soft-start pin has a 11μA charg-
ing current. This pin controls regulated output current
determined by CTRL1.
FB (Pin 7/Pin 10): Feedback Pin for Voltage Regulation
and Overvoltage Protection. The feedback voltage is 1.21V.
Overvoltage is also sensed through the FB pin. When the
feedback voltage exceeds 1.5V, the overvoltage lockout
prevents switching for 13μs to allow the inductor current
to discharge.
SENSE+ (Pin 8/Pin 11):
SENSE+ is the inverting input of
the average current mode loop error amplier. This pin is
connected to the external current sense resistor, RS. The
voltage drop between SENSE+ and SENSE– referenced to
the voltage drop across an internal resistor produces the
input voltages to the current regulation loop.
SENSE– (Pin 9/Pin 12):
SENSE– is the non-inverting input
of the average current mode loop error amplier. The
reference current, based on CTRL1 or CTRL2 ows out of
the pin to the output side of the sense resistor, RS.
VC (Pin 10/Pin 13): VC provides the necessary comp-
ensation for the average current loop stability. Typical
compensation values are 20k to 50k for the resistor and
2nF to 5nF for the capacitor.
RT (Pin 12/Pin 14): A resistor to ground sets the switching
frequency between 200kHz and 1MHz. When using the
SYNC function, set the frequency to be 20% lower than
the SYNC pulse frequency. This pin is current limited to
60μA. Do not leave this pin open.
SYNC (Pin 13/Pin 15): Frequency Synchronization Pin.
This pin allows the switching frequency to be synchronized
to an external clock. The RT resistor should be chosen to
operate the internal clock at 20% slower than the SYNC
pulse frequency. This pin should be grounded when not
in use. When laying out board, avoid noise coupling to
or from SYNC trace.
HG (Pin 15/Pin 17): HG is the top-FET gate drive signal
that controls the state of the high-side external power
FET. The driver pull-up impedance is 2.3Ω and pull-down
impedance is 1.3Ω.
SW (Pin 16/Pin 18): The SW pin is used internally as the
lower-rail for the oating high-side driver. Externally, this
node connects the two power-FETs and the inductor.
CBOOT (Pin 17/Pin 19): The CBOOT pin provides a oat-
ing 5V regulated supply for the high-side FET driver. An
external Schottky diode is required from the VCC_INT pin
to the CBOOT pin to charge the CBOOT capacitor when
the switch-pin is near ground.
LG (Pin 18/Pin 20): LG is the bottom-FET gate drive signal
that controls the state of the low-side external power-FET.
The driver pull-up impedance is 2.3Ω and pull-down
impedance is 1.0Ω.
VCC_INT (Pin 19/Pin 1): A regulated 5V output for charging
the CBOOT capacitor. VCC_INT also provides the power for
the digital and switching subcircuits. Below 6V VIN, tie this
pin to the rail. VCC_INTiscurrentlimitedto50mA.Shutdown
operation disables the output voltage drive.
VIN (Pin 20/Pin 3): Input Supply Pin. Must be locally
bypassed with a 4.7μF low-ESR capacitor to ground.
相關PDF資料 |
PDF描述 |
|---|---|
| LT3741EUF#PBF | SWITCHING CONTROLLER, 1070 kHz SWITCHING FREQ-MAX, PQCC20 |
| LT3741EUF#TRPBF | SWITCHING CONTROLLER, 1070 kHz SWITCHING FREQ-MAX, PQCC20 |
| LT3741IUF#PBF | SWITCHING CONTROLLER, 1070 kHz SWITCHING FREQ-MAX, PQCC20 |
| LT3748HMS#PBF | SWITCHING CONTROLLER, PDSO12 |
| LT3758HMSE#TRPBF | SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3741IUF#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LT3741IUF#PBF | 制造商:Linear Technology 功能描述:DC-DC CONTROLLER BUCK 1MHZ 制造商:Linear Technology 功能描述:DC-DC CONTROLLER, BUCK, 1MHZ, QFN-20 |
| LT3741IUF#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LT3741IUF-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Power, Constant Current, Constant Voltage, Step-Down Controller |
| LT3741IUF-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Power, Constant Current, Constant Voltage, Step-Down Controller |
發布緊急采購，3分鐘左右您將得到回復。