- 您現在的位置：買賣IC網 > PDF目錄44986 > LT3740EDHC (LINEAR TECHNOLOGY CORP) 0.14 A SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, PDSO16 PDF資料下載
參數資料
| 型號： | LT3740EDHC |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.14 A SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | 5 X 3 MM, PLASTIC, MO-229WJED-1, DFN-16 |
| 文件頁數： | 5/20頁 |
| 文件大?。?/td> | 234K |
| 代理商： | LT3740EDHC |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
LT3740
13
3740fc
APPLICATIONS INFORMATION
Checking Transient Response
The regulator loop response can be checked by looking
at the load transient response. Switching regulators take
several cycles to respond to a step in load current. When
a load step occurs, VOUT immediately shifts by an amount
equal to
ΔILOAD*(ESR), where ESR is the effective series
resistance of COUT. ΔILOAD also begins to charge or
discharge COUT generating a feedback error signal used
by the regulator to return VOUT to its steady-state value.
During this recovery time, VOUT can be monitored for
overshoot or ringing that would indicate a stability problem.
The VC pin external components shown in Figure 2 will
provide adequate compensation for most applications. For
a detailed explanation of switching control loop theory see
Application Note 76.
Step-Up Converter Inductor Selection
The step-up converter in the LT3740 provides a BIAS voltage
about 7V higher than the input voltage VIN for the top
MOSFET drive and most of the internal controller circuitry.
The step-up converter has a current limit of 400mA.
An inductor ripple current from 100mA to 200mA is a
reasonable design for the converter. For this consideration,
a 22μH or 47μH inductor is recommended for most of the
LT3740 applications. Small size and high efciency are the
major concerns. Inductors with low core losses and small
DCR at 1MHz are good choices. Some inductors in this
category with small size are listed in Table 2.
Table 2. Recommended Inductors for Step-Up Converter
PART NUMBER
DCR (Ω)
CURRENT
RATING (MA) MANUFACTURER
LQH3C220
0.71
250
Murata
814-237-1431
www.murata.com
ELT5KT-220
0.9
420
Panasonic
714-373-7334
www.panasonic.com
CDRH3D16-220
CR32-470
0.43
0.97
400
330
Sumida
847-956-0666
www.Sumida.com
The step-up converter inductor current is the greatest
when the input voltage is the lowest. Larger Cgs of the
MOSFETs results in large inductor current. Connecting
the BGDP pin to the BIAS pin also greatly increases the
inductor current. The saturation current of the inductor
needs to cover the maximum input current.
The step-up inductor current decreases as the input voltage
increases. For high input voltages, the step-up converter
will begin skipping pulses. Although this will result in some
low frequency ripple, the BIAS voltage remains regulated
on an average basis, and the step-down controller opera-
tion is not affected.
For VIN higher than 10V step-up inductor saturation
current should be higher than 400mA. For VIN lower than
10V, a lower current rating inductor could be used. The
inductor RMS current should be higher than 250mA, and
the inductance should not be less than 10μH at 400mA.
Step-Up Converter Capacitor Selection
Thesmallsizeofceramiccapacitorsmakesthemidealforthe
output of the LT3740 step-up converter. X5R and X7R types
are recommended because they retain their capacitance
over wider voltage and temperature ranges than other types
such as Y5V or Z5U. A 1μF capacitor is recommended for
the output of the LT3740 step-up converter.
Table 3. Recommended Ceramic Capacitor Manufacturers
MANUFACTURER
PHONE
URL
Taiyo Yuden
408-573-4150
www.t-yuden.com
Murata
814-237-1431
www.murata.com
Kemet
408-986-0424
www.kemet.com
Design Example
As a design example, take a supply with the following
specications: VIN = 7V to 20V (15V nominal), VOUT = 2.5V
± 5%, IOUT(MAX) = 10A. First, choose the inductor for about
30% ripple current at nominal VIN:
L
=
2.5V
(300kHz) 0.3 10A
1–
2.5V
15V
= 2.3μH
相關PDF資料 |
PDF描述 |
|---|---|
| LT3741EFE#PBF | SWITCHING CONTROLLER, 1070 kHz SWITCHING FREQ-MAX, PDSO20 |
| LT3741IFE#TRPBF | SWITCHING CONTROLLER, 1070 kHz SWITCHING FREQ-MAX, PDSO20 |
| LT3741EUF#PBF | SWITCHING CONTROLLER, 1070 kHz SWITCHING FREQ-MAX, PQCC20 |
| LT3741EUF#TRPBF | SWITCHING CONTROLLER, 1070 kHz SWITCHING FREQ-MAX, PQCC20 |
| LT3741IUF#PBF | SWITCHING CONTROLLER, 1070 kHz SWITCHING FREQ-MAX, PQCC20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3740EDHC#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 特色產品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 標準包裝:1 系列:PowerWise® PWM 型:電壓模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.5 V ~ 18 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-5°C ~ 125°C 封裝/外殼:32-WFQFN 裸露焊盤 包裝:Digi-Reel® 產品目錄頁面:1303 (CN2011-ZH PDF) 其它名稱:LM3754SQDKR |
| LT3740EDHC#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LT3740EDHC-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Wide Operating Range, Valley Mode, No RSENSE? Synchronous Step-Down Controller |
| LT3740EDHC-TR | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Wide Operating Range, Valley Mode, No RSENSE? Synchronous Step-Down Controller |
| LT3740EDHC-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Wide Operating Range, Valley Mode, No RSENSE? Synchronous Step-Down Controller |
發布緊急采購，3分鐘左右您將得到回復。