- 您現在的位置：買賣IC網 > PDF目錄98002 > LT3587EUD#PBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, 1200 kHz SWITCHING FREQ-MAX, PQCC20 PDF資料下載
參數資料
| 型號： | LT3587EUD#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, 1200 kHz SWITCHING FREQ-MAX, PQCC20 |
| 封裝： | 3 X 3 MM, LEAD FREE, PLASTIC, QFN-20 |
| 文件頁數： | 24/24頁 |
| 文件大?。?/td> | 395K |
| 代理商： | LT3587EUD#PBF |
LT3587
9
3587fc
OPERATION
All three channels of the LT3587 use a constant frequency,
current mode control scheme to provide voltage and/or
current regulation at the output. Operation can be best un-
derstood by referring to the Block Diagram in Figure 1.
If EN/SS1 is pulled higher than 200mV, the bandgap refer-
ence, the start-up bias and the oscillator are turned on. At
the start of each oscillator cycle, the SR latch X1 is set,
which turns on the power switch Q1. A voltage proportional
to the switch current is added to a stabilizing ramp and
the resulting sum is fed into the positive terminal of the
PWM comparator A3. When this voltage exceeds the level
at the negative input of A3, the SR latch X1 is reset, turning
off the power switch Q1. The level at the negative input
of A3 is set by the error amplier A1, which is simply an
amplied version of the difference between the reference
voltage of 1.22V and the feedback voltage. In this manner,
the error amplier sets the correct peak switch current
level to keep the output voltage in regulation. If the error
amplier output increases, more current is delivered to
the output; if it decreases, less current is delivered.
The second channel is an inverting converter. This channel
is also enabled through the EN/SS1 pin. The basic opera-
tion of this second channel is the same as the positive
channel. The SR latch X2 is also set at the start of each
oscillator cycle. The power switch Q2 is turned on at the
same time as Q1. Q2 turns off based on its own feedback
loop, which consists of error amplier A2 and PWM
comparator A4. The reference voltage of this negative
channel is ground.
Voltage clamps (not shown) on the output of the error
ampliers A1 and A2 enforce current limit on Q1 and Q2
respectively.
Similar to the rst channel, the third channel is also a
positive boost regulator. If EN/SS3 is pulled higher than
200mV, the bandgap reference, the start-up bias and the
oscillators are also turned on. The SR latch X3 is set at
the start of each oscillator cycle which turns on the power
switch Q3. Q3 turns off based on its own feedback loop,
which consists of error amplier A5 and PWM comparator
A6. The level at the negative input of A6 is set by the error
amplier A5, and is an amplied version of the difference
between the reference voltage of 0.8V and the maximum
of the two feedback voltages at VFB3 and IFB3. A separate
comparator (not shown) sets the maximum current limit
on Q3.
The IFB3 pin is pulled up internally with a current that
is (1/200) times the load current out of the VOUT3 pin.
Therefore, an external resistor connected from this pin
to ground generates a feedback voltage proportional to
the VOUT3 output load current at the IFB3 pin. When the
voltage at VFB3 is higher than the voltage at IFB3, the third
channel regulates to the feedback voltage at VFB3, which in
normal application is a divided down voltage from VOUT3.
In this state, the third channel behaves as a boost voltage
regulator. On the other hand if the voltage at IFB3 is higher,
the third channel regulates to the feedback voltage at IFB3,
which therefore regulates the VOUT3 output load current to
a particular value. In this state, the third channel behaves
as a boost current regulator.
PMOS M1 is used as an output disconnect pass transistor
for the rst channel. M1 disconnects the load (VOUT1) from
the input as long as the voltage between CAP1 and VIN
is less than 2.5V (typical) and the voltage between CAP1
and VOUT1 is less than 10V (typ). Similarly, PMOS M3 is
used as an output disconnect pass transistor for the third
channel. M3 disconnects the load (VOUT3) from the input
when the third channel is in shutdown (EN/SS3 voltage
is lower than 200mV) and the voltage between CAP3 and
VOUT3 is less than 10V (typical).
相關PDF資料 |
PDF描述 |
|---|---|
| LT3587EUD#TRPBF | SWITCHING REGULATOR, 1200 kHz SWITCHING FREQ-MAX, PQCC20 |
| LT6600CS8#TR | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| LTC1043MD#PBF | SPECIALTY ANALOG CIRCUIT, CDIP18 |
| LTC1043MD883C | SPECIALTY ANALOG CIRCUIT, CDIP18 |
| LTC1147LCS8-3.3#TR | SWITCHING CONTROLLER, 400 kHz SWITCHING FREQ-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3587EUD-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Voltage Monolithic Inverter and Dual Boost |
| LT3590 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:60V Triple Step-Down LED Driver Programmable Temperature Protection |
| LT3590EDC#PBF | 制造商:Linear Technology 功能描述:IC LED DRIVER BULK MODE 48V 制造商:Linear Technology 功能描述:IC, LED DRIVER, BULK MODE, 48V |
| LT3590EDC#TRMPBF | 功能描述:IC LED DRIVER WHITE BCKLGT 6-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:6,000 系列:- 恒定電流:- 恒定電壓:- 拓?fù)?開路漏極，PWM 輸出數:4 內部驅動器:是 類型 - 主要:LED 閃爍器 類型 - 次要:- 頻率:400kHz 電源電壓:2.3 V ~ 5.5 V 輸出電壓:- 安裝類型:表面貼裝 封裝/外殼:8-VFDFN 裸露焊盤 供應商設備封裝:8-HVSON 包裝:帶卷 (TR) 工作溫度:-40°C ~ 85°C 其它名稱:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3590EDC#TRPBF | 功能描述:IC LED DRIVER WHITE BCKLGT 6-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:6,000 系列:- 恒定電流:- 恒定電壓:- 拓?fù)?開路漏極，PWM 輸出數:4 內部驅動器:是 類型 - 主要:LED 閃爍器 類型 - 次要:- 頻率:400kHz 電源電壓:2.3 V ~ 5.5 V 輸出電壓:- 安裝類型:表面貼裝 封裝/外殼:8-VFDFN 裸露焊盤 供應商設備封裝:8-HVSON 包裝:帶卷 (TR) 工作溫度:-40°C ~ 85°C 其它名稱:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
發布緊急采購，3分鐘左右您將得到回復。