參數資料
型號: LT3585EDDB-2
廠商: LINEAR TECHNOLOGY CORP
元件分類: 穩壓器
英文描述: 0.95 A BATTERY CHARGE CONTROLLER, PDSO10
封裝: 3 X 2 MM, PLASTIC, MO-229WECD-1, DFN-10
文件頁數: 19/20頁
文件大?。?/td> 415K
代理商: LT3585EDDB-2
LT3585-0/LT3585-1
LT3585-2/LT3585-3
8
3585f
UU
U
PI FU CTIO S
IGBTIN (Pin 1): Logic Input for the IGBT Driver. When this
pin is driven higher than 1.5V, the output goes high. When
the pin is below 0.5V, the output will go low.
IGBTPWR (Pin 2): Supply Pin for the IGBT Driver. Must be
locally bypassed with a good quality ceramic capacitor. The
minimum operating voltage for the IGBT driver is 2.5V.
GND (Pin 3): Ground. Tie directly to local ground plane.
VIN (Pin 4): Input Supply Pin. Must be locally bypassed
with a good quality ceramic capacitor. The minimum
operating voltage for VIN is 2.5V.
VBAT (Pin 5): Battery Supply Pin. Must be locally bypassed
with a good quality ceramic capacitor. The minimum
operating voltage for VBAT is 1.5V.
DONE (Pin 6): Open NPN Collector Indication Pin. When
target output voltage is reached, NPN turns on. This pin
needs a proper pull-up resistor or current source.
CHRG/IADJ (Pin 7): Charge and Input Current Adjust Pin.
A low (< 0.3V) to high (>1.1V) transition on this pin puts
the part into power delivery mode. Once the target output
voltage is reached, the part will stop charging the output.
Toggle this pin to start charging again. Ground to shut
down. To enter into the input current reduction mode, the
voltage on this pin should be driven high ( >1.1V ) and
then oated. (For more information refer to the Operation
section of this data sheet.) To enter normal mode, the
voltage should be driven higher than 1.6V.
SW (Pin 8): Switch Pin. This is the collector of the internal
NPN Power switch. Minimize the metal trace area connected
to this pin to minimize EMI. Tie one side of the primary
of the transformer to this pin. The target output voltage
is set by the turns ratio of the transformer.
Choose turns ratio N by the following equation:
N
VOUT
=
+ 2
31 5
.
where VOUT is the desired output voltage.
IGBTPD (Pin 9): Pull-down Output for IGBT Gate. Connect
this pin to the IGBT Gate. Add a series resistor to increase
the turn-off time to protect the IGBT.
IGBTPU (Pin 10): Pull-up Output for IGBT Gate. Connect
this pin to the gate of the IGBT.
Exposed Pad (Pin 11): Ground. Tie directly to local ground
plane.
相關PDF資料
PDF描述
LT3585EDDB-0#TRMPDF 1.3 A BATTERY CHARGE CONTROLLER, PDSO10
LT3585EDDB-3 1.85 A BATTERY CHARGE CONTROLLER, PDSO10
LT3587EUD#PBF SWITCHING REGULATOR, 1200 kHz SWITCHING FREQ-MAX, PQCC20
LT3587EUD#TRPBF SWITCHING REGULATOR, 1200 kHz SWITCHING FREQ-MAX, PQCC20
LT6600CS8#TR SPECIALTY ANALOG CIRCUIT, PDSO8
相關代理商/技術參數
參數描述
LT3585EDDB-2#PBF 制造商:Linear Technology 功能描述:Photo Flash Charger 10-Pin DFN EP
LT3585EDDB-2#TRPBF 功能描述:IC CHARGER PHOTOFLASH 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP(4x4) 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR
LT3585EDDB-3 制造商:LINER 制造商全稱:Linear Technology 功能描述:Photofl ash Chargers with Adjustable Input Current and IGBT Drivers
LT3585EDDB-3#TRPBF 功能描述:IC CHARGER PHOTOFLASH 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP(4x4) 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR
LT3587 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Voltage Monolithic Inverter and Dual Boost