- 您現在的位置：買賣IC網 > PDF目錄44985 > LT3509EDE#PBF (LINEAR TECHNOLOGY CORP) 1.2 A DUAL SWITCHING CONTROLLER, 2500 kHz SWITCHING FREQ-MAX, PDSO14 PDF資料下載
參數資料
| 型號： | LT3509EDE#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.2 A DUAL SWITCHING CONTROLLER, 2500 kHz SWITCHING FREQ-MAX, PDSO14 |
| 封裝： | 4 X 3 MM, LEAD FREE, PLASTIC, MO-229WGED-3, DFN-14 |
| 文件頁數： | 21/24頁 |
| 文件大?。?/td> | 271K |
| 代理商： | LT3509EDE#PBF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁
LT3509
6
3509fc
PIN FUNCTIONS
DA1, DA2 (Pins 1, 7/Pins 1, 8): The DA pins are the anode
connections for the catch diodes. These are connected
internally to the exposed ground pad by current sensing
resistors.
BOOST1, BOOST2 (Pins 2, 6/Pins 2, 7): The BOOST pins
are used to dynamically boost the power transistor base
above VIN to minimize the voltage drop and power loss in
the switch. These should be tied to the associated switch
pins through the boost capacitors.
SW1, SW2 (Pins 3, 5/Pins 3, 6): The SW pins are the
internal power switch outputs. These should be connected
to the associated inductors, catch diode cathodes, and the
boost capacitors.
VIN (Pin 4/Pins 4, 5): The VIN pins supply power to the
internal power switches and control circuitry. In the MSE
package the VIN pins must be tied together. The input
capacitor should be placed as close as possible to the
supply pins.
FB1, FB2 (Pins 14, 8/Pins 16, 9): The FB pins are used
to set the regulated output voltage relative to the internal
reference. These pins should be connected to a resistor
divider from the regulated output such that the FB pin is
at 0.8V when the output is at the desired voltage.
RUN/SS1, RUN/SS2 (Pins 13, 9/Pins 15, 10): The RUN/SS
pins enable the associated regulator channel. If both pins
are pulled to ground, the device will shut-down to a low
power state. In the range 0.8V to 2V, the regulators are
enabled but the peak switch current and the DA pin maxi-
mum current are limited to provide a soft-start function.
Above 2V, the full output current is available. The inputs
incorporate a 1μA pull-up so that they will oat high or
charge an external capacitor to provide a current limited
soft-start. The pins are pulled down by approximately 250μA
in the case of overvoltage or overtemperature conditions
in order to discharge the soft-start capacitors. The pins
can also be driven by a logic control signal of up to 5.0V.
In this case, it is necessary place a 10k to 50k resistor
in series along with a capacitor from the RUN/SS pin to
ground to ensure that there will be a soft-start for both
initial turn on and in the case of fault conditions. Do not
tie these pins to VIN.
RT (Pin 10/Pin 11): The RT pin is used to set the internal
oscillator frequency. A 40.2k resistor from RT to ground
results in a nominal frequency of 1MHz.
SYNC (Pin 11/Pin12): The SYNC pin allows the switching
frequency to be synchronized to a external clock. Choose
RT resistor to set a free-run frequency at least 12% less
than the external clock frequency for correct operation.
BD (Pin 12/Pin 13): The BD pin is common anode connec-
tion of the internal Schottky boost diodes. This provides
the power for charging the BOOST capacitors. It should
be locally bypassed for best performance.
Exposed Pad (Pin 15/Pin 17): GND. This is the reference
and supply ground for the regulator. The exposed pad
must be soldered to the PCB and electrically connected to
supply ground. Use a large ground plane and thermal vias
to optimize thermal performance. The current in the catch
diodes also ows through the GND pad to the DA pins.
AGND (Pin 14, MSOP Package Only): This is the connected
to the ground connection of the chip and may be used as a
separate return for the low current control side components.
It should not be used as the only ground connection or as
a connection return for load side components.
(DFN/MSOP)
相關PDF資料 |
PDF描述 |
|---|---|
| LT3509EDE#TRPBF | 1.2 A DUAL SWITCHING CONTROLLER, 2500 kHz SWITCHING FREQ-MAX, PDSO14 |
| LT3570EFE#TRPBF | 3.1 A SWITCHING REGULATOR, 2750 kHz SWITCHING FREQ-MAX, PDSO20 |
| LT3570IUF#PBF | 3.1 A SWITCHING REGULATOR, 2750 kHz SWITCHING FREQ-MAX, PQCC24 |
| LT3570EFE#PBF | 3.1 A SWITCHING REGULATOR, 2750 kHz SWITCHING FREQ-MAX, PDSO20 |
| LT3570IUF#TRPBF | 3.1 A SWITCHING REGULATOR, 2750 kHz SWITCHING FREQ-MAX, PQCC24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3509EDE-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual 36V, 700mA Step-Down Regulator |
| LT3509EMSE#PBF | 功能描述:IC REG BUCK ADJ 0.7A DL 16MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LT3509EMSE#TRPBF | 功能描述:IC REG BUCK ADJ 0.7A DL 16MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LT3509EMSEPBF | 制造商:Linear Technology 功能描述:Conv DC-DC Dual Step-Down 3.6-36V MSOP16 |
| LT3509EMSE-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual 36V, 700mA Step-Down Regulator |
發布緊急采購，3分鐘左右您將得到回復。