參數資料
型號: LT3493EDCB-3#TR
廠商: LINEAR TECHNOLOGY CORP
元件分類: 穩壓器
英文描述: 2.2 A SWITCHING REGULATOR, 815 kHz SWITCHING FREQ-MAX, PDSO6
封裝: 2 X 3 MM, PLASTIC, MO-229, DFN-6
文件頁數: 20/20頁
文件大?。?/td> 401K
代理商: LT3493EDCB-3#TR
9
LT3493-3
3493-3f
Minimum On Time
The part will still regulate the output at input voltages that
exceed VIN(PS) (up to 40V), however, the output voltage
ripple increases as the input voltage is increased. Figure 1
illustrates switching waveforms in continuous mode for a
3V output application near VIN(PS) = 33V.
As the input voltage is increased, the part is required to
switch for shorter periods of time. Delays associated with
turning off the power switch dictate the minimum on time
of the part. The minimum on time for the LT3493-3 is
130ns. Figure 2 illustrates the switching waveforms when
the input voltage is increased to VIN = 35V.
Now the required on time has decreased below the mini-
mum on time of 130ns. Instead of the switch pulse width
becoming narrower to accommodate the lower duty cycle
requirement, the switch pulse width remains fixed at
130ns. In Figure 2 the inductor current ramps up to a value
exceeding the load current and the output ripple increases
to ~200mV. The part then remains off until the output
voltage dips below 100% of the programmed value before
it begins switching again.
Provided that the output remains in regulation and that the
inductor does not saturate, operation above VIN(PS) is safe
and will not damage the part. Figure 3 illustrates the
switching waveforms when the input voltage is increased
to its absolute maximum rating of 40V.
APPLICATIO S I FOR ATIO
WU
U
Figure 3
As the input voltage increases, the inductor current ramps
up quicker, the number of skipped pulses increases and
the output voltage ripple increases. For operation above
VIN(MAX) the only component requirement is that the
components be adequately rated for operation at the
intended voltage levels.
The part is robust enough to survive prolonged operation
under these conditions as long as the peak inductor
current does not exceed 2.2A. Inductor current saturation
may further limit performance in this operating regime.
Inductor Selection and Maximum Output Current
A good first choice for the inductor value is:
L = 1.6 (VOUT + VD)
where VD is the voltage drop of the catch diode (~0.4V) and
L is in
H. With this value there will be no subharmonic
oscillation for applications with 50% or greater duty cycle.
The inductor’s RMS current rating must be greater than
your maximum load current and its saturation current
should be about 30% higher. For robust operation in fault
conditions, the saturation current should be above 2.2A.
To keep efficiency high, the series resistance (DCR) should
be less than 0.1
. Table 1 lists several vendors and types
that are suitable.
Of course, such a simple design guide will not always
result in the optimum inductor for your application. A
VSW
20V/DIV
VOUT
200mV/DIV
AC COUPLED
COUT = 10F
VOUT = 3V
VIN = 40V
ILOAD = 0.75A
L = 10
H
2
s/DIV
3493-3 F03
IL
0.5A/DIV
VSW
20V/DIV
VOUT
200mV/DIV
AC COUPLED
COUT = 10F
VOUT = 3V
VIN = 35V
ILOAD = 0.75A
L = 10
H
2
s/DIV
3493-3 F02
IL
0.5A/DIV
Figure 2
相關PDF資料
PDF描述
LT3494EDDB#PBF 0.25 A SWITCHING REGULATOR, PDSO8
LT3494EDDB 0.25 A SWITCHING REGULATOR, PDSO8
LT3502AEDC#PBF 1.1 A SWITCHING REGULATOR, 2800 kHz SWITCHING FREQ-MAX, PDSO8
LT3502AIDC#PBF 1.1 A SWITCHING REGULATOR, 2800 kHz SWITCHING FREQ-MAX, PDSO8
LT3502AIDC#TR 1.1 A SWITCHING REGULATOR, 2800 kHz SWITCHING FREQ-MAX, PDSO10
相關代理商/技術參數
參數描述
LT3493EDCBPBF 制造商:LT 功能描述:Pb Free
LT3493EDCB-PBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.2A, 750kHz Step-Down Switching Regulator in 2mm × 3mm DFN
LT3493EDCB-TR 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.2A, 750kHz Step-Down Switching Regulator in 2mm × 3mm DFN
LT3493EDCBTRMPBF 制造商:Linear Technology 功能描述:Sw. Regulator 1.2A 750kHz Step-Down DFN6
LT3493EDCB-TRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.2A, 750kHz Step-Down Switching Regulator in 2mm × 3mm DFN