參數資料
型號: LT303EMSE#TRPBF
廠商: LINEAR TECHNOLOGY CORP
元件分類: 穩壓器
英文描述: 0.55 A FLUORESCENT LIGHT CONTROLLER, PDSO10
封裝: LEAD FREE, PLASTIC, MSOP-10
文件頁數: 13/16頁
文件大?。?/td> 211K
代理商: LT303EMSE#TRPBF
LT3003
6
3003fa
The LT3003 is an easy-to-use 3-channel LED ballaster.
It allows three strings of LEDs to be driven in parallel
with accurate LED current matching. A PWM pin is also
provided allowing LED currents to be turned on and off at
very low duty cycles for very wide LED dimming ranges.
For reliable system thermal management, two output ags,
OT1 and OT2, are provided to indicate when the junction
temperature exceeds 125°C.
The Block Diagram in Figure 1 best illustrates the features
of LT3003. The LT3003 internal bias circuitry is turned on
when VIN > 3V and SHDN > 0.7V. For LED current to be
active in each channel, the PWM pin must exceed 0.5V.
VMAX should be connected to the highest supply in the
application (see various application modes of boost, buck,
buck-boost in the Typical Applications section).
The LT3003 ballasting feature is achieved by using the
current monitored in the LED2 channel to control the
current in channels LED1 and LED3. A servo loop exists
for each channel LED1 and LED3 that compares the cur-
rent in each channel to the LED2 reference channel. The
current in LED2 channel is determined by the LED current
programmed by the partner LED driver. Details of how LED
current can be programmed by the partner IC are covered
in the Typical Applications section using various ICs as
LED drivers. Maximum fault current in each of the LT3003
LED pins is internally limited to 550mA. If any LED string
experiences an open-circuit fault, all LED string currents
are turned off.
The LT3003 PWM pin has unique level-shifting circuitry to
allow a simple logic-level PWM signal to turn each LED pin
current on and off regardless of the VEE pin voltage. This
allows very simple PWM dimming control of LED current
without any need for external level-shifting components
in buck mode and buck-boost mode applications. Care is
taken to ensure low current (nano amps) in the VEE and
VMAX pins 10s after PWM low edge. This feature mini-
mizes leakage currents in each application to maximize
PWM dimming ratio. Details of PWM dimming and criti-
cal parameters are given in the Applications Information
section PWM Dimming.
The LT3003 incorporates internal junction temperature
sensing and provides two open-collector outputs, OT1
and OT2, which become active low when junction tem-
perature exceeds 125°C. OT1 is sized to pull 100A and
can be used as an input to the microprocessor for system
thermal management. OT2 is sized to pull 300A to defeat
switching for most of LTC’s LED drivers by pulling down
the gm error amplier output. LT3003 is forced to a “zero
LED current state” by a special internal protection circuit
when junction temperature reaches 150°C.
To calculate the LT3003 junction temperature, see Thermal
Calculations in the Applications Information section.
OPERATION
相關PDF資料
PDF描述
LT3503EDCB 1 A SWITCHING REGULATOR, 2400 kHz SWITCHING FREQ-MAX, PDSO6
LT3585EDDB-2 0.95 A BATTERY CHARGE CONTROLLER, PDSO10
LT3585EDDB-0#TRMPDF 1.3 A BATTERY CHARGE CONTROLLER, PDSO10
LT3585EDDB-3 1.85 A BATTERY CHARGE CONTROLLER, PDSO10
LT3587EUD#PBF SWITCHING REGULATOR, 1200 kHz SWITCHING FREQ-MAX, PQCC20
相關代理商/技術參數
參數描述
LT30400-1 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:Class T Fuse Blocks - 300 and 600 Volt
LT304001C 功能描述:熔絲座 ACS 300C Class T 400A 1 Pole RoHS:否 制造商:Littelfuse 產品: 電流額定值:30 A 電壓額定值:1000 VDC 極數:1 系列: 安裝風格:DIN Rail 端接類型: 軸類型: 工作溫度范圍:
LT3046 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | BJT | NPN | 200MA I(C) | TO-46
LT-3047 制造商:LEADERTECH INC 功能描述:13-28U-MAG CONTACT SERIES
LT3050 制造商:LINER 制造商全稱:Linear Technology 功能描述:50mA, 3V to 80V Low Dropout Micropower Linear Regulator