PD = (63." />
參數資料
型號: LT1886CS8#PBF
廠商: Linear Technology
文件頁數: 2/16頁
文件大?。?/td> 0K
描述: IC OPAMP DUAL 200MA 700MHZ 8SOIC
標準包裝: 100
放大器類型: 通用
電路數: 2
轉換速率: 200 V/µs
增益帶寬積: 700MHz
電流 - 輸入偏壓: 1.5µA
電壓 - 輸入偏移: 1000µV
電流 - 電源: 7mA
電流 - 輸出 / 通道: 800mA
電壓 - 電源,單路/雙路(±): 4 V ~ 13 V,±2 V ~ 6.5 V
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 8-SOIC(0.154",3.90mm 寬)
供應商設備封裝: 8-SO
包裝: 管件
10
LT1886
APPLICATIO S I FOR ATIO
WU
U
The dissipation for the amplifiers is:
PD = (63.5mA)(12V) – (4V/√2)2/(50) = 0.6W
The total package power dissipation is 0.6W. When a 2500
sq. mm PC board with 2oz copper on top and bottom is
used, the thermal resistance is 80
°C/W. The junction
temperature TJ is:
TJ = (0.6W)(80°C/W) + 85°C = 133°C
The maximum junction temperature for the LT1886 is
150
°C so the heat sinking capability of the board is
adequate for the application.
If the copper area on the PC board is reduced to 180 sq.
mm the thermal resistance increases to 122
°C/W and the
junction temperature becomes:
TJ = (0.6W)(122°C/W) + 85°C = 158°C
which is above the maximum junction temperature indi-
cating that the heat sinking capability of the board is
inadequate and should be increased.
Capacitive Loading
The LT1886 is stable with a 1000pF capacitive load. The
photo of the small-signal response with 1000pF load in a
gain of 10 shows 50% overshoot. The photo of the large-
signal response with a 1000pF load shows that the output
slew rate is not limited by the short-circuit current. The
Typical Performance Curve of Frequency Response vs
Capacitive Load shows the peaking for various capacitive
loads.
This stability is useful in the case of directly driving a
coaxial cable or twisted pair that is inadvertently
unterminated. For best pulse fidelity, however, a termina-
tion resistor of value equal to the characteristic impedance
of the cable or twisted pair (i.e., 50
/75/100/135)
should be placed in series with the output. The other end
of the cable or twisted pair should be terminated with the
same value resistor to ground.
Compensation
The LT1886 is stable in a gain 10 or higher for any supply
and resistive load. It is easily compensated for lower gains
with a single resistor or a resistor plus a capacitor.
Figure 2 shows that for inverting gains, a resistor from the
inverting node to AC ground guarantees stability if the
parallel combination of RC and RG is less than or equal to
RF/9. For lowest distortion and DC output offset, a series
capacitor, CC, can be used to reduce the noise gain at lower
frequencies. The break frequency produced by RC and CC
should be less than 15MHz to minimize peaking. The
Typical Curve of Frequency Response vs Supply Voltage,
AV = –1 shows less than 1dB of peaking for a break
frequency of 12.8MHz.
+
6V
–6V
909
100
100
+
1886 F01
1K
50
–4V
4V
f = 1MHz
Figure 1. Thermal Calculation Example
RG
RC
Vo
Vi
CC
(OPTIONAL)
+
1886 F02
RF
=
–RF
RG
Vo
Vi
< 15MHz
1
2
πRCCC
(RC || RG) ≤ RF/9
Figure 2. Compensation for Inverting Gains
Figure 3 shows compensation in the noninverting configu-
ration. The RC, CC network acts similarly to the inverting
case. The input impedance is not reduced because the
network is bootstrapped. This network can also be placed
between the inverting input and an AC ground.
Another compensation scheme for noninverting circuits is
shown in Figure 4. The circuit is unity gain at low frequency
and a gain of 1 + RF/RG at high frequency. The DC output
offset is reduced by a factor of ten. The techniques of
相關PDF資料
PDF描述
LT1886CS8 IC OPAMP DUAL 200MA 700MHZ 8SOIC
LT1881CS8#TRPBF IC OPAMP DUAL R-R PICO/IN 8-SOIC
LT1881CS8#TR IC OPAMP DUAL R-R PICO/IN 8SOIC
929715-01-11-I CONN HEADER 22POS DUAL .100 STR
LT1884CS8#TRPBF IC OPAMP DUAL R-R PICO/IN 8SOIC
相關代理商/技術參數
參數描述
LT1893-11-0125 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PHOTOTRANSISTOR | NPN | DOME-5.0
LT18E-Q21-LU0X3-H1141 制造商:TURCK Inc 功能描述:LT0102
LT190 制造商:Cooper Wiring Devices 功能描述:
LT190Z 制造商:SEOUL 制造商全稱:Seoul Semiconductor 功能描述:GREEN OVAL LAMP LED
LT191 制造商:SEOUL 制造商全稱:Seoul Semiconductor 功能描述:BLUE OVAL LAMP LED