- 您現在的位置：買賣IC網 > PDF目錄385501 > LT1676 (Linear Technology Corporation) Wide Input Range, High Efficiency, Step-Down Switching Regulator(寬輸入范圍，高效率，步降開關穩壓器) PDF資料下載
參數資料
| 型號： | LT1676 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Wide Input Range, High Efficiency, Step-Down Switching Regulator(寬輸入范圍，高效率，步降開關穩壓器) |
| 中文描述： | 輸入范圍寬，高效率，降壓型開關穩壓器（寬輸入范圍，高效率，步降開關穩壓器） |
| 文件頁數： | 11/16頁 |
| 文件大小： | 140K |
| 代理商： | LT1676 |
11
LT1676
i.e., SHDN, SYNC, V
C
and FB. This can cause erratic
operation such as odd/even cycle behavior, pulse width
“nervousness”, improper output voltage and/or prema-
ture current limit action.
As an example, assume that the capacitance between the
V
SW
node and a high impedance pin node is 0.1pF, and
further assume that the high impedance node in question
exhibits a capacitance of 1pF to ground. Due to the high
dV/dt, large excursion behavior of the V
SW
node, this will
couple a nearly 5V transient to the high impedance pin,
causing abnormal operation. (This assumes the “typical”
48V
IN
to 5V
OUT
application.) An explicit 100pF capacitor
added to the node will reduce the amplitude of the distur-
bance to more like 50mV (although settling time will
increase).
Specific pin recommendations are as follows:
SHDN: If unused, add a 100pF capacitor to ground.
SYNC: Ground if unused.
V
C
: Add a capacitor directly to ground in addition to the
explicit compensation network. A value of one-tenth of
the main compensation capacitor is recommended, up
to a maximum of 100pF.
FB: Assuming the V
C
pin is handled properly, this pin
usually requires no explicit capacitor of its own, but
keep this node physically small to minimize stray ca-
pacitance.
APPLICATIO
S I
FOR
ATIO
U
W
U
U
frequency resonance problems, proper layout of the com-
ponents connected to the IC is essential, especially the
power path. B field (magnetic) radiation is minimized by
keeping output diode, switch pin and intput bypass
capacitor leads as short as possible. E field radiation is
kept low by minimizing the length and area of all traces
connected to the switch pin (V
SW
). A ground plane should
always be used under the switcher circuitry to prevent
interplane coupling.
The high speed switching current path is shown schemati-
cally in Figure 3. Minimum lead length in these paths is
essential to ensure clean switching and minimal EMI. The
paths containing the input capacitor, output switch and
output diode are the only ones containing nanosecond rise
and fall times. Keep these paths as short as possible.
Additionally, it is possible for the LT1676 to cause EMI
problems by “coupling to itself”. Specifically, this can
occur if the V
SW
pin is allowed to capacitively couple in an
uncontrolled manner to the part’s high impedance nodes,
+
+
LT1676
V
SW
C1
D1
L1
V
IN
V
OUT
V
IN
C2
1676 F03
Figure 3. High Speed Current Switching Paths
TYPICAL APPLICATIO
N
S
Minimum Component Count Application
Figure 4a shows a basic “minimum component count”
application. The circuit produces 5V at up to 500mA I
OUT
with input voltages in the range of 12V to 48V. The typical
P
OUT
/P
IN
efficiency is shown in Figure 4b. No pulse
skipping is observed down to zero external load. As
shown, the SHDN and SYNC pins are unused, however
either (or both) can be optionally driven by external signals
as desired.
User Programmable Undervoltage Lockout
Figure 5 adds a resistor divider to the basic application.
This is a simple, cost-effective way to add a user-program-
mable undervoltage lockout (UVLO) function. Resistor R5
is chosen to have approximately 200
μ
A through it at the
nominal SHDN pin lockout threshold of roughly 1.25V.
The somewhat arbitrary value of 200
μ
A was chosen to be
significantly above the SHDN pin input current to minimize
its error contribution, but significantly below the typical
3.2mA the LT1676 draws in lockout mode. Resistor R4 is
then chosen to yield this same 200
μ
A, less 2.5
μ
A, with the
相關PDF資料 |
PDF描述 |
|---|---|
| LT1677 | Low Noise, Rail-to-Rail Precision Op Amp(低噪聲，滿幅度輸入和輸出精密運算放大器) |
| LT1684 | Micropower Ring Tone Generator |
| LT1684CN | Micropower Ring Tone Generator |
| LT1684CS | Micropower Ring Tone Generator |
| LT1684IN | Micropower Ring Tone Generator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1676C | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Wide Input Range, High Efficiency, Step-Down Switching Regulator |
| LT1676CN8 | 功能描述:IC REG BUCK ADJ 0.7A 8DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LT1676CN8#PBF | 功能描述:IC REG BUCK ADJ 0.7A 8DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LT1676CS8 | 功能描述:IC REG BUCK ADJ 0.7A 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LT1676CS8#PBF | 功能描述:IC REG BUCK ADJ 0.7A 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
發布緊急采購，3分鐘左右您將得到回復。