- 您現在的位置：買賣IC網 > PDF目錄44981 > LT1576IS8#TR (LINEAR TECHNOLOGY CORP) 3.5 A SWITCHING REGULATOR, 240 kHz SWITCHING FREQ-MAX, PDSO8 PDF資料下載
參數資料
| 型號： | LT1576IS8#TR |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 3.5 A SWITCHING REGULATOR, 240 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | 0.150 INCH, PLASTIC, SOP-8 |
| 文件頁數： | 25/28頁 |
| 文件大?。?/td> | 290K |
| 代理商： | LT1576IS8#TR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁
6
LT1576/LT1576-5
PIN FUNCTIONS
UU
U
VSW (Pin 1): The switch pin is the emitter of the on-chip
power NPN switch. This pin is driven up to the input pin
voltage during switch on time. Inductor current drives the
switch pin negative during switch off time. Negative volt-
age is clamped with the external catch diode. Maximum
negative switch voltage allowed is – 0.8V.
VIN (Pin 2): This is the collector of the on-chip power NPN
switch. This pin powers the internal circuitry and internal
regulator when the BIAS pin is not present. At NPN switch
on and off, high dI/dt edges occur on this pin. Keep the
external bypass and catch diode close to this pin. All trace
inductance on this path will create a voltage spike at switch
off, adding to the VCE voltage across the internal NPN.
BOOST (Pin 3): The BOOST pin is used to provide a drive
voltage, higher than the input voltage, to the internal
bipolar NPN power switch. Without this added voltage, the
typical switch voltage loss would be about 1.5V. The
additional boost voltage allows the switch to saturate and
voltage loss approximates that of a 0.2
FET structure.
Efficiency improves from 75% for conventional bipolar
designs to > 88% for these new parts.
GND (Pin 4): The GND pin connection needs consideration
for two reasons. First, it acts as the reference for the
regulated output, so load regulation will suffer if the
“ground” end of the load is not at the same voltage as the
GND pin of the IC. This condition will occur when load
current or other currents flow through metal paths be-
tween the GND pin and the load ground point. Keep the
ground path short between the GND pin and the load and
use a ground plane when possible. The second consider-
ation is EMI caused by GND pin current spikes. Internal
capacitance between the VSW pin and the GND pin creates
very narrow (<10ns) current spikes in the GND pin. If the
GND pin is connected to system ground with a long metal
trace, this trace may radiate excess EMI. Keep the path
between the input bypass and the GND pin short.
BIAS (Pin 5): The BIAS pin is used to improve efficiency
when operating at higher input voltages and light load
current. Connecting this pin to the regulated output volt-
age forces most of the internal circuitry to draw its
operating current from the output voltage rather than the
input supply. This is a much more efficient way of doing
business if the input voltage is much higher than the
output.
Minimum output voltage setting for this mode of
operation is 3.3V. Efficiency improvement at VIN = 20V,
VOUT = 5V, and IOUT = 25mA is over 10%.
VC (Pin 6): The VC pin is the output of the error amplifier
and the input of the peak switch current comparator. It is
normally used for frequency compensation, but can do
double duty as a current clamp or control loop override.
BOOST Pin Current
SWITCH CURRENT (A)
0
BOOST
PIN
CURRENT
(mA)
30
25
20
15
10
5
0
0.25
0.50
0.75
1.00
1576 G19
1.25
1.50
VC Pin Shutdown Threshold
JUNCTION TEMPERATURE (
°C)
–50
1.0
0.8
0.6
0.4
0.2
0
100
1576 G20
–25
0
25
50
75
125
THRESHOLD
VOLTAGE
(V)
TYPICAL PERFORMANCE CHARACTERISTICS
UW
相關PDF資料 |
PDF描述 |
|---|---|
| LT1634CMS8-2.5#PBF | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PDSO8 |
| LT1634CMS8-1.25#PBF | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.25 V, PDSO8 |
| LT1634CMS8-1.25#TRPBF | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.25 V, PDSO8 |
| LT1680ISW#TRPBF | SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT1702-7FB1 | 1-OUTPUT 500 W AC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1577 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Ultrafast Transient Response, Low Dropout Regulators Adjustable and Fixed |
| LT1577CS-3.3/2.8 | 功能描述:IC REG CTRLR DUAL OUT 16SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性晶體管驅動器 系列:- 產品培訓模塊:More Information on LDOs 標準包裝:2,500 系列:- 類型:正，固定式 輸出數:2 輸出電壓:2.8V，3.3V 電流 - 電源:12mA 輸入電壓:5 V ~ 22 V 工作溫度:0°C ~ 70°C 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| LT1577CS-3.3/2.8#PBF | 功能描述:IC REG CTRLR DUAL OUT 16SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性晶體管驅動器 系列:- 產品培訓模塊:More Information on LDOs 標準包裝:2,500 系列:- 類型:正，固定式 輸出數:2 輸出電壓:2.8V，3.3V 電流 - 電源:12mA 輸入電壓:5 V ~ 22 V 工作溫度:0°C ~ 70°C 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| LT1577CS-3.3/2.8#TR | 功能描述:IC REG CTRLR DUAL OUT 16SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性晶體管驅動器 系列:- 產品培訓模塊:More Information on LDOs 標準包裝:2,500 系列:- 類型:正，固定式 輸出數:2 輸出電壓:2.8V，3.3V 電流 - 電源:12mA 輸入電壓:5 V ~ 22 V 工作溫度:0°C ~ 70°C 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| LT1577CS-3.3/2.8#TRPBF | 功能描述:IC REG CTRLR DUAL OUT 16SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性晶體管驅動器 系列:- 產品培訓模塊:More Information on LDOs 標準包裝:2,500 系列:- 類型:正，固定式 輸出數:2 輸出電壓:2.8V，3.3V 電流 - 電源:12mA 輸入電壓:5 V ~ 22 V 工作溫度:0°C ~ 70°C 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。