參數資料
型號: LT1222MJ8
廠商: LINEAR TECHNOLOGY CORP
元件分類: 運動控制電子
英文描述: 500MHz Operational Amplifier
中文描述: OP-AMP, 600 uV OFFSET-MAX, 500 MHz BAND WIDTH, CDIP8
封裝: 0.300 INCH, HERMETIC SEALED, CERDIP-8
文件頁數: 7/12頁
文件大小: 312K
代理商: LT1222MJ8
7
LT1222
APPLICATIO
S I
FOR
ATIO
U
Output Clamping
Access to the internal compensation node at pin 5 allows
the output swing of the LT1222 to be clamped. An example
is shown on the first page of this data sheet. The compen-
sation node is approximately one diode drop above the
output and can source or sink 1.2mA. Back-to-back Schot-
tky diodes clamp pin 5 to a diode drop above ground so the
output is clamped to
±
0.5V (the drop of the Schottkys at
1.2mA). The diode reference is bypassed for good AC
response. This circuit is useful for amplifying the voltage at
false sum nodes used in settling time measurements.
W
U
U
Capacitive Loading
The LT1222 is stable with capacitive loads. This is accom-
plished by sensing the load induced output pole and adding
compensation at the amplifier gain node. As the capacitive
load increases, both the bandwidth and phase margin
decrease. There will be peaking in the frequency domain as
shown in the curve of Frequency Response vs Capacitive
Load. The small-signal transient response will have more
overshoot as shown in the photo of the small-signal
response with 1000pF load. The large-signal response with
a 10,000pF load shows the output slew rate being limited
to 4V/
μ
s by the short-circuit current. The LT1222 can drive
coaxial cable directly, but for best pulse fidelity a resistor of
value equal to the characteristic impedance of the cable
(i.e., 75
) should be placed in series with the output. The
other end of the cable should be terminated with the same
value resistor to ground.
Compensation
The LT1222 has a typical gain-bandwidth product of
500MHz which allows it to have wide bandwidth in high
gain configurations (i.e., in a gain of 100, it will have a
bandwidth of about 5MHz). For added flexibility the ampli-
fier frequency response may be adjusted by adding capaci-
tance from pin 5 to ground. The compensation capacitor
may be used to reduce overshoot, to allow the amplifier to
be used in lower noise gains, or simply to reduce band-
width. Table 1 shows gain and compensation capacitor
vresus –3dB bandwidth, maximum frequency peaking and
small-signal overshoot.
Table 1
A
V
–1
–1
–1
–1
5
5
5
5
10
10
10
10
20
20
20
C
C
(pF)
30
50
82
150
10
20
30
50
0
5
10
20
0
5
10
f
–3dB
(MHz)
99
70
32
13
140
100
34
15
150
111
40
17
82
24
14
Max Peaking (dB)
4.2
0.9
0
0
3.8
0
0
0
9.5
0.2
0
0
0.1
0
0
Overshoot (%)
36
13
0
0
35
5
1
0
45
10
2
0
10
0
0
For frequencies < 10MHz the frequency response of the
amplifier is approximately:
f = 1/[2
π
×
53
×
(C
C
+ 6pF)
×
(Noise Gain)]
The slew rate is affected as follows:
SR = 1.2mA/(C
C
+ 6pF)
An example would be a gain of –10 (noise gain of 11) and
C
C
= 20pF which has 10.5MHz bandwidth and 46V/
μ
s slew
rate. It should be noted that the LT1222 is not stable in
A
V
= 1 unless C
C
= 50pF and a 1k resistor is used as the
feedback resistor. The 1k and input capacitance increase
the noise gain at frequency to aid stability.
相關PDF資料
PDF描述
LT1225 Very High Speed Operational Amplifier(超高速運算放大器)
LT1226 Low Noise Very High Speed Operational Amplifier(低噪聲,超高速運算放大器)
LT1227 140MHz Video Current Feedback Amplifier(140MHz ,視頻電流反饋放大器)
LT1228 100MHz Current Feedback Amplifier with DC Gain Control(100MHz ,電流反饋放大器(帶直流增益控制))
LT1229 Dual 100MHz Current Feedback Amplifiers(雙路,100MHz ,電流反饋放大器)
相關代理商/技術參數
參數描述
LT1223 制造商:LINER 制造商全稱:Linear Technology 功能描述:100MHz Current Feedback Amplifier
LT1223_05 制造商:LINER 制造商全稱:Linear Technology 功能描述:100MHz Current Feedback Amplifier
LT1223C 制造商:LINER 制造商全稱:Linear Technology 功能描述:100MHz Current Feedback Amplifier
LT1223CJ8 制造商:LINER 制造商全稱:Linear Technology 功能描述:100MHz Current Feedback Amplifier
LT1223CN8 制造商:Linear Technology 功能描述:OP Amp Single Current Fdbk ±15V 8-Pin PDIP N