- 您現在的位置：買賣IC網 > PDF目錄385498 > LT1175 (Linear Technology Corporation) 500mA Negative Low Dropout Micropower Regulator(500mA,F負輸出，低壓差，微功耗穩壓器) PDF資料下載
參數資料
| 型號： | LT1175 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 500mA Negative Low Dropout Micropower Regulator(500mA,F負輸出，低壓差，微功耗穩壓器) |
| 中文描述： | 500mA的低壓差微負穩壓器（500mA的，女負輸出，低壓差，微功耗穩壓器） |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 124K |
| 代理商： | LT1175 |
9
LT1175
APPLICATIO
S I
FOR
ATIO
U
W
U
U
during a “shorting out” surge, only during a “charge up”
surge.
The output capacitor should be located within several
inches of the regulator. If remote sensing is used, the
output capacitor can be located at the remote sense node,
but the GND pin of the regulator should also be connected
to the remote site. The basic rule is to keep SENSE and
GND pins close to the output capacitor, regardless of
where it is.
Operating at very large input-to-output differential volt-
ages (>5V) with load currents less than 5mA requires an
output capacitor with an ESR greater than 1
to prevent
low level output oscillations.
Input Capacitor
The LT1175 requires a separate input bypass capacitor
only if the regulator is located more than six inches from
the raw supply output capacitor. A 1
μ
F or larger tantalum
capacitor is suggested for all applications, but if low ESR
capacitors such as ceramic or film are used for the output
and input capacitors, the input capacitor should be at least
three times the value of the output capacitor. If a solid
tantalum or aluminum electrolytic output capacitor is
used, the input capacitor is very noncritical.
High Temperature Operation
The LT1175 is a micropower design with only 45
μ
A
quiescent current. This could make it perform poorly at
high temperatures (>125
°
C), where power transistor leak-
age might exceed the output node loading current (5
μ
A to
15
μ
A). To avoid a condition where the output voltage drifts
uncontrolled high during a high temperature no-load
condition, the LT1175 has an active load which turns on
when the output is pulled above the nominal regulated
voltage. This load absorbs power transistor leakage and
maintains good regulation. There is one downside to this
feature, however. If the output is pulled high deliberately,
as it might be when the LT1175 is used as a backup to a
slightly higher output from a primary regulator, the LT1175
will act as an unwanted load on the primary regulator.
Because of this, the active pull-down is deliberately “weak.”
It can be modeled as a 2k resistor in series with an internal
clamp voltage when the regulator output is being pulled
Die
V
V
I
Maximum
T
T
V
JA
IN
OUT
LOAD
A
JA
A
JA LOAD
OUT
Temp = T +
Power Dissipation = T
for Thermal Considerations
MAX
MAX
θ
θ
θ
(
)(
)
)
+
high. If a 4.8V output is pulled to 5V, for instance, the load
on the primary regulator would be (5V – 4.8V)/2k
=
100
μ
A. This also means that if the internal pass transistor
leaks 50
μ
A, the output voltage will be (50
μ
A)(2k
) =
100mV high. This condition will not occur under normal
operating conditions, but could occur immediately after
an output short circuit had overheated the chip.
Thermal Considerations
The LT1175 is available in a special 8-pin surface mount
package which has Pins 1 and 8 connected to the die attach
paddle. This reduces thermal resistance when Pins 1 and
8 are connected to expanded copper lands on the PC
board. Table 2 shows thermal resistance for various
combinations of copper lands and backside or internal
planes. Table 2 also shows thermal resistance for the 5-pin
DD surface mount package and the 8-pin DIP and package.
Table 2. Package Thermal Resistance (
°
C/W)
LAND AREA
Minimum
Minimum with
Backplane
1cm
2
Top Plane
with Backplane
10cm
2
Top Plane
with Backplane
DIP
140
110
ST
90
70
SO
100
80
Q
60
50
100
64
75
35
80
50
60
27
To calculate die temperature, maximum power dissipation
or maximum input voltage, use the following formulas
with correct thermal resistance numbers from Table 2. For
through-hole TO-220 applications use
θ
JA
= 50
°
C/W
without a heat sink and
θ
JA
= 5
°
C/W + heat sink thermal
resistance when using a heat sink.
Maximum Input Voltage
相關PDF資料 |
PDF描述 |
|---|---|
| LT1187IN8 | Low Power Video Difference Amplifi er |
| LT1188 | 10-bit Bus Interface Flip-Flops With 3-State Outputs 24-SOIC 0 to 70 |
| LT1188C | 1.5A High Side Switch |
| LT1188CK | 1.5A High Side Switch |
| LT1188CT | 1.5A High Side Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1175_05 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:500mA Negative Low Dropout Micropower Regulator |
| LT1175_10 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:500mA Negative Low Dropout Micropower Regulator |
| LT1175-5 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Precision Micropower RMS-to-DC Converter |
| LT1175C | 制造商:LINER 制造商全稱:Linear Technology 功能描述:500mA Negative Low Dropout Micropower Regulator |
| LT1175CN8 | 功能描述:IC REG LDO NEG ADJ .5A 8-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:800 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:2.5V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.7V @ 4A 穩壓器數量:1 電流 - 輸出:4A 電流 - 限制（最?。?4.2A 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-6，D²Pak（5 引線+接片），TO-263BA 供應商設備封裝:TO-263-5 包裝:帶卷 (TR) 其它名稱:AP1184K525L-13AP1184K525LDITR |
發布緊急采購，3分鐘左右您將得到回復。