- 您現在的位置：買賣IC網 > PDF目錄385498 > LT1173 (Linear Technology Corporation) Micropower DC/DC Converter Adjustable and Fixed 5V, 12V(微功耗，固定輸出12V或5V及可調輸出，DC/DC變換器（工作于步升和步降兩種模式）) PDF資料下載
參數資料
| 型號： | LT1173 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Micropower DC/DC Converter Adjustable and Fixed 5V, 12V(微功耗，固定輸出12V或5V及可調輸出，DC/DC變換器（工作于步升和步降兩種模式）) |
| 中文描述： | 微功率DC / DC轉換可調和固定5V，12V的（微功耗，固定輸出12V的或5V的及可調輸出，直流/直流變換器（工作于步升和步降兩種模式）） |
| 文件頁數： | 7/16頁 |
| 文件大?。?/td> | 256K |
| 代理商： | LT1173 |
LT1173
7
As an example, suppose 9V at 50mA is to be generated
from a 3V input. Recalling Equation 02,
P
L
= (9V + 0.5V – 3V) (50mA) = 325mW.
Energy required from the inductor is
(07)
P
F
mW
kHz
J
L
OSC
=
=
( )
325
24
13 5
08
.
.
μ
Picking an inductor value of 100
μ
H with 0.2
DCR results
in a peak switch current of
i
V
e
mA
PEAK
s
H
=
=
( )
3
1
1
616
09
1
23
μ
100
–
.
–
μ
Substituting i
PEAK
into Equation 04 results in
E
H
A
J
L
=
(
)(
)
=
( )
1
2
100
0 616
.
19 0
10
2
μ
μ
.
.
Since 19
μ
J > 13.5
μ
J the 100
μ
H inductor will work. This
trial-and-error approach can be used to select the opti-
mum inductor. Keep in mind the switch current maximum
rating of 1.5A. If the calculated peak current exceeds this,
consider using the LT1073. The 70% duty cycle of the
LT1073 allows more energy per cycle to be stored in the
inductor, resulting in more output power.
An inductor’s energy storage capability is proportional to
its physical size. If the size of the inductor is too large for
a particular application, considerable size reduction is
possible by using the LT1111. This device is pin compat-
ible with the LT1173 but has a 72kHz oscillator, thereby
reducing inductor and capacitor size requirements by a
factor of three.
For both positive-to-negative (Figure 7) and negative-to-
positive configurations (Figure 8), all the output power
must be generated by the inductor. In these cases
P
L
= (
V
OUT
+ V
D
) (I
OUT
).
In the positive-to-negative case, switch drop can be mod-
eled as a 0.75V voltage source in series with a 0.65
resistor so that
V
L
= V
IN
– 0.75V – I
L
(0.65
).
(11)
(12)
In the negative-to-positive case, the switch saturates and
the 0.8
switch ON resistance value given for Equation 04
can be used. In both cases inductor design proceeds from
Equation 03.
The step-down case is different than the preceeding three
in that the inductor current flows through the load in a
step-down topology (Figure 6). Current through the switch
should be limited to ~650mA in step-down mode. This can
be accomplished by using the I
LIM
pin. With input voltages
in the range of 12V to 25V, a 5V output at 300mA can be
generated with a 220
μ
H inductor and 100
resistor in
series with the I
LIM
pin. With a 20V to 30V input range, a
470
μ
H inductor should be used along with the 100
resistor.
Capacitor Selection
Selecting the right output capacitor is almost as important
as selecting the right inductor. A poor choice for a filter
capacitor can result in poor efficiency and/or high output
ripple. Ordinary aluminum electrolytics, while inexpensive
and readily available, may have unacceptably poor equiva-
lent series resistance (ESR) and ESL (inductance). There
are low-ESR aluminum capacitors on the market specifi-
cally designed for switch mode DC-DC converters which
work much better than general-purpose units. Tantalum
capacitors provide still better performance at more ex-
pense. We recommend OS-CON capacitors from Sanyo
Corporation (San Diego, CA). These units are physically
quite small and have extremely low ESR. To illustrate,
Figures 2, 3, and 4 show the output voltage of an LT1173
based converter with three 100
μ
F capacitors. The peak
switch current is 500mA in all cases. Figure 2 shows a
Sprague 501D, 25V aluminum capacitor. V
OUT
jumps by
over 120mV when the switch turns off, followed by a drop
in voltage as the inductor dumps into the capacitor. This
works out to be an ESR of over 240m
. Figure 3 shows the
same circuit, but with a Sprague 150D, 20V tantalum
capacitor replacing the aluminum unit. Output jump is
now about 35mV, corresponding to an ESR of 70m
.
Figure 4 shows the circuit with a 16V OS-CON unit. ESR is
now only 20m
.
U
S
A
O
PPLICATI
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LT1175 | 500mA Negative Low Dropout Micropower Regulator(500mA,F負輸出，低壓差，微功耗穩壓器) |
| LT1187IN8 | Low Power Video Difference Amplifi er |
| LT1188 | 10-bit Bus Interface Flip-Flops With 3-State Outputs 24-SOIC 0 to 70 |
| LT1188C | 1.5A High Side Switch |
| LT1188CK | 1.5A High Side Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1173-12 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Micropower DC/DC Converter Adjustable and Fixed 5V, 12V |
| LT1173-5 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Micropower DC/DC Converter Adjustable and Fixed 5V, 12V |
| LT1173CN8 | 功能描述:IC REG BUCK BST INV ADJ .4A 8DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LT1173CN8#PBF | 功能描述:IC REG BUCK BST INV ADJ .4A 8DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:MIC23xxx HyperLight Load™ Regulators 標準包裝:5,000 系列:HyperLight Load® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.8V 輸入電壓:2.7 V ~ 5.5 V PWM 型:混合物 頻率 - 開關:4MHz 電流 - 輸出:2A 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-VFDFN 裸露焊盤，8-MLF? 包裝:帶卷 (TR) 供應商設備封裝:8-MLF?（2x2） 產品目錄頁面:1094 (CN2011-ZH PDF) 其它名稱:576-3303-2 |
| LT1173CN8-12 | 功能描述:IC REG BUCK BST INV 12V .4A 8DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
發布緊急采購，3分鐘左右您將得到回復。