- 您現在的位置：買賣IC網 > PDF目錄385498 > LT1172 (Linear Technology Corporation) 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C PDF資料下載
參數資料
| 型號： | LT1172 |
| 廠商： | Linear Technology Corporation |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C |
| 中文描述： | 射頻放大器 |
| 文件頁數： | 8/20頁 |
| 文件大?。?/td> | 275K |
| 代理商： | LT1172 |
8
LT1170/LT1171/LT1172
function; when pulled low with an external resistor, it
programs the LT1170/LT1171/LT1172 to disconnect the
main error amplifier output and connects the output of the
flyback amplifier to the comparator input. The LT1170/
LT1171/LT1172 will then regulate the value of the flyback
pulse with respect to the supply voltage.* This flyback
pulse is directly proportional to output voltage in the
traditional transformer coupled flyback topology regula-
tor. By regulating the amplitude of the flyback pulse, the
output voltage can be regulated with no direct connection
between input and output. The output is fully floating up to
the breakdown voltage of the transformer windings. Mul-
tiple floating outputs are easily obtained with additional
windings. A special delay network inside the LT1170/
LT1171/LT1172 ignores the leakage inductance spike at
the leading edge of the flyback pulse to improve output
regulation.
The error signal developed at the comparator input is
brought out externally. This pin (V
C
) has four different
functions. It is used for frequency compensation, current
limit adjustment, soft starting, and total regulator shut-
down. During normal regulator operation this pin sits at a
voltage between 0.9V (low output current) and 2.0V (high
output current). The error amplifiers are current output
(g
m
) types, so this voltage can be externally clamped for
adjusting current limit. Likewise, a capacitor coupled
external clamp will provide soft start. Switch duty cycle
goes to zero if the V
C
pin is pulled to ground through a
diode, placing the LT1170/LT1171/LT1172 in an idle mode.
Pulling the V
C
pin below 0.15V causes total regulator
shutdown, with only 50
μ
A supply current for shutdown
circuitry biasing. See AN19 for full application details.
Extra Pins on the MiniDIP and Surface Mount Packages
The 8- and 16-pin versions of the LT1172 have the
emitters of the power transistor brought out separately
from the ground pin. This eliminates errors due to ground
pin voltage drops and allows the user to reduce switch
current limit 2:1 by leaving the second emitter (E2) discon-
nected. The first emitter (E1) should always be connected
to the ground pin. Note that switch “on” resistance doubles
when E2 is left open, so efficiency will suffer somewhat
when switch currents exceed 300mA. Also, note that chip
dissipation will actually increasewith E2 open during
normal load operation, even though dissipation in current
limit mode will decrease See “Thermal Considerations”
next.
Thermal Considerations When Using the MiniDIP and
SW Packages
The low supply current and high switch efficiency of the
LT1172 allow it to be used without a heat sink in most
applications when the TO-220 or TO-3 package is se-
lected. These packages are rated at 50
°
C/W and 35
°
C/W
respectively. The miniDIPs, however, are rated at 100
°
C/W
in ceramic (J) and 130
°
C/W in plastic (N).
Care should be taken for miniDIP applications to ensure
that the worst case input voltage and load current condi-
tions do not cause excessive die temperatures. The follow-
ing formulas can be used as a rough guide to calculate
LT1172 power dissipation. For more details, the reader is
referred to Application Note 19 (AN19), “Efficiency Calcu-
lations” section.
Average supply current (including driver current) is:
I
IN
≈
6mA + I
SW
(0.004 + DC/40)
I
SW
= switch current
DC = switch duty cycle
Switch power dissipation is given by:
P
SW
= (I
SW
)
2
(R
SW
)(DC)
R
SW
= LT1172 switch “on” resistance (1
maximum)
Total power dissipation is the sum of supply current times
input voltage plus switch power:
P
D(TOT)
= (I
IN
)(V
IN
) + P
SW
In a typical example, using a boost converter to generate
12V at 0.12A from a 5V input, duty cycle is approximately
60%, and switch current is about 0.65A, yielding:
I
IN
= 6mA + 0.65(0.004 + DC/40) = 18mA
P
SW
= (0.65)
2
(1
)(0.6) = 0.25W
P
D(TOT)
= (5V)(0.018A) + 0.25 = 0.34W
*See note under block diagram.
OPERATIOU
相關PDF資料 |
PDF描述 |
|---|---|
| LT1173 | Micropower DC/DC Converter Adjustable and Fixed 5V, 12V(微功耗，固定輸出12V或5V及可調輸出，DC/DC變換器（工作于步升和步降兩種模式）) |
| LT1175 | 500mA Negative Low Dropout Micropower Regulator(500mA,F負輸出，低壓差，微功耗穩壓器) |
| LT1187IN8 | Low Power Video Difference Amplifi er |
| LT1188 | 10-bit Bus Interface Flip-Flops With 3-State Outputs 24-SOIC 0 to 70 |
| LT1188C | 1.5A High Side Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1172C | 制造商:LINER 制造商全稱:Linear Technology 功能描述:100kHz, 5A, 2.5A and 1.25A High Efficiency Switching Regulators |
| LT1172CJ8 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:100kHz, 5A, 2.5A and 1.25A High Efficiency Switching Regulators |
| LT1172CK | 制造商:LINER 制造商全稱:Linear Technology 功能描述:100kHz, 5A, 2.5A and 1.25A High Efficiency Switching Regulators |
| LT1172CN8 | 功能描述:IC REG MULTI CONFIG ADJ 8DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LT1172CN8#PBF | 功能描述:IC REG MULTI CONFIG ADJ 8DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
發布緊急采購，3分鐘左右您將得到回復。