- 您現在的位置：買賣IC網 > PDF目錄385498 > LT1021 (Linear Technology Corporation) Precision Reference(精密電壓基準（可調：5V, 7V和10V）) PDF資料下載
參數資料
| 型號： | LT1021 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Precision Reference(精密電壓基準（可調：5V, 7V和10V）) |
| 中文描述： | 精密參考（精密電壓基準（可調：5V的，7伏和10V時）） |
| 文件頁數： | 9/16頁 |
| 文件大小： | 215K |
| 代理商： | LT1021 |
9
LT1021
APPLICATIO
S I
N
FOR
ATIO
U
Effect of Reference Drift on System Accuracy
A large portion of the temperature drift error budget in
many systems is the system reference voltage. This graph
indicates the maximum temperature coefficient allowable
if the reference is to contribute no more than 0.5LSB error
to the overall system performance. The example shown is
a 12-bit system designed to operate over a temperature
range from 25
°
C to 65
°
C. Assuming the system calibra-
tion is performed at 25
°
C, the temperature span is 40
°
C.
It can be seen from the graph that the temperature coeffi-
cient of the reference must be no worse than 3ppm/
°
C if
it is to contribute less than 0.5LSB error. For this reason,
the LT1021 family has been optimized for low drift.
W
U
Maximum Allowable Reference Drift
Trimming Output Voltage
LT1021-10
The LT1021-10 has a trim pin for adjusting output voltage.
The impedance of the trim pin is about 12k
with a
nominal open-circuit voltage of 5V. It is designed to be
driven from a source impedance of 3k
or less to mini-
mize changes in the LT1021 TC with output trimming.
Attenuation between the trim pin and the output is 70:1.
This allows
±
70mV trim range when the trim pin is tied to
the wiper of a potentiometer connected between the
output and ground. A 10k
potentiometer is recom-
mended, preferably a 20 turn cermet type with stable
characteristics over time and temperature.
The LT1021-10 “C” version is pre-trimmed to
±
5mV and
therefore can utilize a restricted trim range. A 75k resistor
in series with a 20k
potentiometer will give
±
10mV trim
range. Effect on the output TC will be only 1ppm/
°
C for the
±
5mV trim needed to set the “C” device to 10.000V.
LT1021-5
The LT1021-5 does have an output voltage trim pin, but
the TC of the nominal 4V open-circuit voltage at this pin is
about –1.7mV/
°
C. For the voltage trimming not to affect
reference output TC, the external trim voltage must track
the voltage on the trim pin. Input impedance of the trim pin
is about 100k
and attenuation to the output is 13:1. The
technique shown below is suggested for trimming the
output of the LT1021-5 while maintaining minimum shift
in output temperature coefficient. The R1/R2 ratio is
chosen to minimize interaction of trimming and TC shifts,
so the exact values shown should be used.
LT1021-5
OUT
TRIM
IN
GND
R1
27k
R2
50k
1N4148
V
OUT
1021 AI02
TEMPERATURE SPAN (
°
C)
10
0
M
0
°
C
30
100
LT1021 AI01
1.0
10
20
100
90
80
70
60
50
40
8-BIT
10-BIT
12-BIT
14-BIT
LT1021-7
The 7V version of the LT1021 has no trim pin because the
internal architecture does not have a point which could be
driven conveniently from the output. Trimming must
therefore be done externally, as is the case with ordinary
reference diodes. Unlike these diodes, however, the out-
put of the LT1021 can be loaded with a trim potentiometer.
The following trim techniques are suggested; one for
voltage output and one for current output. The voltage
output is trimmed for 6.95V. Current output is 1mA, as
shown, into a summing junction, but all resistors may be
scaled for currents up to 10mA.
Both of these circuits use the trimmers in a true potentio-
metric mode to reduce the effects of trimmer TC. The
voltage output has a 200
impedance, so loading must be
相關PDF資料 |
PDF描述 |
|---|---|
| LT1022 | High Speed, Precision JFET Input Op Amp(高速，精密，結型場效應管輸入運算放大器) |
| LT1025 | Micropower,Thermocouple Cold Junction Compensator(微功耗，熱電偶冷端補償器) |
| LT1031 | Precision 10V Reference(10V精密電壓基準) |
| LT1038 | 10Amp Positive Adjustable Voltage Regulator |
| LT1038C | Dual J-K Negative-Edge-Triggered Flip-Flops With Clear and Preset 16-PDIP 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1021BCH-5 | 功能描述:IC VREF SERIES BURIED ZENER TO-5 RoHS:否 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:- 標準包裝:2,000 系列:- 基準類型:旁路，可調節，精度 輸出電壓:1.24 V ~ 16 V 容差:±0.5% 溫度系數:- 輸入電壓:1.24 V ~ 16 V 通道數:1 電流 - 陰極:100µA 電流 - 靜態:- 電流 - 輸出:20mA 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:TO-226-3、TO-92-3（TO-226AA）成形引線 供應商設備封裝:TO-92-3 包裝:帶卷 (TR) |
| LT1021BCN8-10 | 功能描述:IC VREF SERIES SHUNT ZNR 8-PDIP RoHS:否 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:- 標準包裝:2,000 系列:- 基準類型:旁路，可調節，精度 輸出電壓:1.24 V ~ 16 V 容差:±0.5% 溫度系數:- 輸入電壓:1.24 V ~ 16 V 通道數:1 電流 - 陰極:100µA 電流 - 靜態:- 電流 - 輸出:20mA 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:TO-226-3、TO-92-3（TO-226AA）成形引線 供應商設備封裝:TO-92-3 包裝:帶卷 (TR) |
| LT1021BCN8-10#PBF | 功能描述:IC VREF SERIES SHUNT ZNR 8-PDIP RoHS:是 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:- 標準包裝:3,000 系列:- 基準類型:旁路，精度 輸出電壓:3V 容差:±0.5% 溫度系數:100ppm/°C 輸入電壓:- 通道數:1 電流 - 陰極:82µA 電流 - 靜態:- 電流 - 輸出:15mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-TSSOP（5 引線），SC-88A，SOT-353 供應商設備封裝:SC-70-5 包裝:帶卷 (TR) 其它名稱:296-20888-2 |
| LT1021BCN8-10#PBF | 制造商:Linear Technology 功能描述:IC VOLTAGE REFERENCE 10V DIP-8 制造商:Linear Technology 功能描述:IC, VOLTAGE REFERENCE, 10V, DIP-8 |
| LT1021BCN8-5 | 功能描述:IC VREF SERIES BURIED ZNR 8-PDIP RoHS:否 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:- 標準包裝:2,000 系列:- 基準類型:旁路，可調節，精度 輸出電壓:1.24 V ~ 16 V 容差:±0.5% 溫度系數:- 輸入電壓:1.24 V ~ 16 V 通道數:1 電流 - 陰極:100µA 電流 - 靜態:- 電流 - 輸出:20mA 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:TO-226-3、TO-92-3（TO-226AA）成形引線 供應商設備封裝:TO-92-3 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。