參數資料
型號： LT1014AJ
廠商： Texas Instruments, Inc.
英文描述： QUAD PRECISION OPERATIONAL AMPLIFIERS
中文描述： 四高精度運算放大器
文件頁數： 19/30頁
文件大小： 631K
代理商： LT1014AJ
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039C – JULY 1989 – REVISED SEPTEMBER 1999
19
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
comparator applications
The single-supply operation of the LT1014 can be used as a precision comparator with TTL-compatible output.
In systems using both operational amplifiers and comparators, the LT1014 can perform multiple duties (see
Figures 25 and 26).
Figure 25. Low-to-High-Level Output Response
for Various Input Overdrives
100 mV
10 mV
5 mV
2 mV
D
I
t – Time –
μ
s
Overdrive
VCC+ = 5 V
VCC– = 0
TA = 25
°
C
–
V
O
5
4
3
2
1
0
0
50
100 150 200 250 300 350 400 450
Figure 26. High-to-Low-Level Output Response
for Various Input Overdrives
2 mV
5 mV
100 mV
Overdrive
10 mV
D
I
t – Time –
μ
s
VCC+ = 5 V
VCC– = 0
TA = 25
°
C
–
V
O
5
4
3
2
1
0
0
50
100 150 200 250 300 350 400 450
low-supply operation
The minimum supply voltage for proper operation of the LT1014 is 3.4 V (three Ni-Cad batteries). Typical supply
current at this voltage is 290
μ
A; therefore, power dissipation is only 1 mW per amplifier.
offset voltage and noise testing
Figure 30 shows the test circuit for measuring input offset voltage and its temperature coefficient. This circuit
with supply voltages increased to
±
20 V is also used as the burn-in configuration.
The peak-to-peak equivalent input noise voltage of the LT1014 is measured using the test circuit shown in
Figure 27. The frequency response of the noise tester indicates that the 0.1-Hz corner is defined by only one
zero. The test time to measure 0.1-Hz to 10-Hz noise should not exceed 10 seconds, as this time limit acts as
an additional zero to eliminate noise contribution from the frequency band below 0.1 Hz.
An input noise-voltage test is recommended when measuring the noise of a large number of units. A 10-Hz input
noise-voltage measurement correlates well with a 0.1-Hz peak-to-peak noise reading because both results are
determined by the white noise and the location of the 1/f corner frequency.
Noise current is measured by the circuit and formula shown in Figure 28. The noise of the source resistors is
subtracted.
相關PDF資料
PDF描述
LT1014AN CAPACITOR, CER, .47UF,16V,+80/-20%
LT1014DJ QUAD PRECISION OPERATIONAL AMPLIFIERS
LT1014DMN QUAD PRECISION OPERATIONAL AMPLIFIERS
LT1014DW CAP 10UF 6.3V 0805
LT1014FK CAP\CER CHIP\X7R AND REGULAR NPO 22UF 0805 X5R 6.3V 20% MARKED
相關代理商/技術參數
參數描述
LT1014AMFK 制造商:TI 制造商全稱:Texas Instruments 功能描述:QUAD PRECISION OPERATIONAL AMPLIFIERS
LT1014AMFKB 制造商:Texas Instruments 功能描述:
LT1014AMJ 制造商:Linear Technology 功能描述:OP Amp Quad GP ±22V/44V 14-Pin CDIP 制造商:Texas Instruments 功能描述:OP Amp Quad GP ±22V/44V 14-Pin CDIP Tube 制造商:Texas Instruments 功能描述:OP AMP QUAD GP 22V/44V 14CDIP - Rail/Tube
LT1014AMJ/883 制造商:Linear Technology 功能描述:OP Amp Quad GP ±22V/44V 14-Pin CDIP
LT1014AMJB 制造商:Texas Instruments 功能描述:OP Amp Quad GP ±22V/44V 14-Pin CDIP Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*