參數資料
型號: LT1013A
廠商: Texas Instruments, Inc.
元件分類: 速度傳感器和接近開關
英文描述: Proximity Sensor; Sensor Input Type:Inductive; Sensing Range Max:8mm; Sensor Output Type:NO; Sensor Housing:Barrel
中文描述: 雙高精度運算放大器
文件頁數: 19/25頁
文件大?。?/td> 420K
代理商: LT1013A
LT1013, LT1013A, LT1013D, LT1013Y
DUAL PRECISION OPERATIONAL AMPLIFIERS
SLOS018B – MAY 1988 – REVISED OCTOBER 1996
19
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
single-supply operation
The LT1013 is fully specified for single-supply operation (V
CC–
= 0). The common-mode input voltage range
includes ground, and the output swings to within a few millivolts of ground.
Furthermore, the LT1013 has specific circuitry that addresses the difficulties of single-supply operation, both
at the input and at the output. At the input, the driving signal can fall below 0 V, either inadvertently or on a
transient basis. If the input is more than a few hundred millivolts below ground, the LT1013 is designed to deal
with the following two problems that can occur:
1.
On many other operational amplifiers, when the input is more than a diode drop below ground, unlimited
current will flow from the substrate (V
CC–
terminal) to the input, which can destroy the unit. On the
LT1013, the 400-
resistors in series with the input (see schematic) protect the device even when the
input is 5 V below ground.
2.
When the input is more than 400 mV below ground (at T
A
= 25
°
C), the input stage of similar type
operational amplifiers saturates and phase reversal occurs at the output. This can cause lock up in
servo systems. Because of a unique phase-reversal protection circuitry (Q21, Q22, Q27, and Q28), the
LT1013 outputs do not reverse, even when the inputs are at –1.5 V (see Figure 24).
This phase-reversal protection circuitry does not function when the other operational amplifier on the LT1013
is driven hard into negative saturation at the output. Phase-reversal protection does not work on amplifier 1
when 2’s output is in negative saturation or on amplifier 2 when 1’s output is in negative saturation.
At the output, other single-supply designs either cannot swing to within 600 mV of ground or cannot sink more
than a few microproamperes while swinging to ground. The all-NPN output stage of the LT1013 maintains its
low output resistance and high gain characteristics until the output is saturated. In dual-supply operations, the
output stage is free of crossover distortion.
(a) VI(PP) = –1.5 V TO 4.5 V
(b) OUTPUT PHASE REVERSAL
EXHIBITED BY LM358
(c) NO PHASE REVERSAL
EXHIBITED BY LT1013
–1
0
1
2
3
4
5
–1
0
1
2
3
4
5
–1
0
1
2
3
4
5
–2
I
VO
V
Figure 24. Voltage-Follower Response With Input Exceeding
the Negative Common-Mode Input Voltage Range
相關PDF資料
PDF描述
LT1013P DUAL PRECISION OPERATIONAL AMPLIFIERS
LT1013YJG DUAL PRECISION OPERATIONAL AMPLIFIERS
LT1013YFK DUAL PRECISION OPERATIONAL AMPLIFIERS
LT1013IN8 Quad Precision Op Amp
LT1013ACN8 Quad Precision Op Amp
相關代理商/技術參數
參數描述
LT1013ACH 制造商:LINER 制造商全稱:Linear Technology 功能描述:Quad Precision Op Amp (LT1014) Dual Precision Op Amp (LT1013)
LT1013ACJ8 制造商:Linear Technology 功能描述:OP Amp Dual GP ±22V/44V 8-Pin CDIP
LT1013ACJG 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier
LT1013ACL 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier
LT1013ACN8 功能描述:IC PRECISION OP-AMP DUAL 8-DIP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:73 系列:Over-The-Top® 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.07 V/µs 增益帶寬積:200kHz -3db帶寬:- 電流 - 輸入偏壓:1nA 電壓 - 輸入偏移:285µV 電流 - 電源:50µA 電流 - 輸出 / 通道:25mA 電壓 - 電源,單路/雙路(±):2 V ~ 44 V,±1 V ~ 22 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WFDFN 裸露焊盤 供應商設備封裝:16-DFN-EP(5x3) 包裝:管件