參數資料
型號: LSP5503SEC
廠商: LITE-ON SEMICONDUCTOR CORP
元件分類: 穩壓器
英文描述: 4 A SWITCHING REGULATOR, 470 kHz SWITCHING FREQ-MAX, PDSO8
封裝: SOP-8
文件頁數: 7/12頁
文件大?。?/td> 475K
代理商: LSP5503SEC
LSP5503
3A Synchronous Step Down DC/DC Converter
4 of 12
Rev. 1.8
APPLICATION INFORMATION
Output Voltage Setting
Figure1. Output Voltage Setting
Figure 1 shows the connections for setting the output voltage. Select the proper ratio of the two feedback resistors
RFB1 and RFB2 based on the output voltage. Typically, use RFB2 ≈ 10k and determine RFB1 from the following
equation:
(1)
Inductor Selection
The inductor maintains a continuous current to the output load. This inductor current has a ripple that is dependent
on the inductance value: higher inductance reduces the peak-to-peak ripple current. The trade off for high
inductance value is the increase in inductor core size and series resistance, and the reduction in current handling
capability. In general, select an inductance value L based on the ripple current requirement:
RIPPLE
OUTMAX
SW
IN
OUT
IN
OUT
K
I
f
V
)
V
(
V
L
=
(2)
where VIN is the input voltage, VOUT is the output voltage, fSW is the switching frequency, IOUTMAX is the maximum
output current, and KRIPPLE is the ripple factor. Typically, choose KRIPPLE = 30% to correspond to the peak-to-peak
ripple current being 30% of the maximum output current.
With this inductor value, the peak inductor current is IOUT (1 + KRIPPLE / 2). Make sure that this peak inductor current
is less that the 4A current limit. Finally, select the inductor core size so that it does not saturate at 4A. Typical
inductor values for various output voltages are shown in Table 1.
VOUT 1.0V 1.2V 1.5V 1.8V 2.5V 3.3V
5V
L
4.7uH 4.7uH 4.7uH 4.7uH 6.8H 6.8H 10H
Table 1. Typical Inductor Values
Input Capacitor
The input capacitor needs to be carefully selected to maintain sufficiently low ripple at the supply input of the
converter. A low ESR capacitor is highly recommended. Since large current flows in and out of this capacitor during
switching, its ESR also affects efficiency.
The input capacitance needs to be higher than 10F. The best choice is the ceramic type; however, low ESR
tantalum or electrolytic types may also be used provided that the RMS ripple current rating is higher than 50% of the
output current. The input capacitor should be placed close to the IN and G pins of the IC, with the shortest traces
possible. In the case of tantalum or electrolytic types, they can be further away if a small parallel 0.1F ceramic
capacitor is placed right next to the IC.
相關PDF資料
PDF描述
LT1004IDRG4-1-2 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.235 V, PDSO8
LT1004CLP-2-5 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PBCY3
LT1004IPW-2-5 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PDSO8
LT1004CPWRE4-2-5 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PDSO8
LT1004CDE4-1-2 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.235 V, PDSO8
相關代理商/技術參數
參數描述
LSP5526-S8A 制造商:Lite-On Semiconductor Corporation 功能描述:
LSP5A 功能描述:限位開關 Limit SW/Single Pole Plug-in RoHS:否 制造商:Honeywell 觸點形式:SPDT 執行器:Non-Contact 電流額定值:30 mA 電壓額定值 AC: 電壓額定值 DC:3.6 V 工作力:10 g IP 等級:IP 67 NEMA 額定值:1, 4, 12, 13 端接類型:4-Pin M12 Connector 安裝:SMD/SMT
LSP5A7 功能描述:限位開關 LIMIT SWITCH RoHS:否 制造商:Honeywell 觸點形式:SPDT 執行器:Non-Contact 電流額定值:30 mA 電壓額定值 AC: 電壓額定值 DC:3.6 V 工作力:10 g IP 等級:IP 67 NEMA 額定值:1, 4, 12, 13 端接類型:4-Pin M12 Connector 安裝:SMD/SMT
LSP600212001 制造商:Link Com 功能描述:
LSP600212001-50 制造商:LINKCOM 制造商全稱:LinkCom Manufacturing Co., Ltd. 功能描述:AC TO DC LED POWER SUPPLY