參數資料
型號： LSM330DL
廠商： STMICROELECTRONICS
元件分類： 模擬信號調理
英文描述： SPECIALTY ANALOG CIRCUIT, PBGA28
封裝： 7.50 X 4.40 MM, 1.10 MM HEIGHT, GREEN, PLASTIC, LGA-28
文件頁數： 17/54頁
文件大?。?/td> 1064K
代理商： LSM330DL
Digital interfaces
LSM330DL
24/54
Doc ID 022018 Rev 1
5.2
SPI bus interface
The LSM330DL SPI is a bus slave. The SPI allows to write and read the registers of the
device.
The Serial Interface interacts with the outside world with 4 wires: CS, SPC, SDI and SDO
(SPC, SDI, SD0 are common).
Figure 6.
Read and write protocol
CS is the serial port enable and it is controlled by the SPI master. It goes low at the start of
the transmission and goes back high at the end. SPC is the serial port clock and it is
controlled by the SPI master. It is stopped high when CS is high (no transmission). SDI and
SDO are, respectively, the serial port data input and output. These lines are driven at the
falling edge of SPC and should be captured at the rising edge of SPC.
Both the read register and write register commands are completed in 16 clock pulses or in
multiples of 8 in case of multiple read/write bytes. Bit duration is the time between two falling
edges of SPC. The first bit (bit 0) starts at the first falling edge of SPC after the falling edge
of CS, while the last bit (bit 15, bit 23, ...) starts at the last falling edge of SPC just before the
rising edge of CS.
bit 0: RW bit. When 0, the data DI(7:0) is written into the device. When 1, the data DO(7:0)
from the device is read. In the latter case, the chip will drive SDO at the start of bit 8.
bit 1: MS bit. When 0, the address will remain unchanged in multiple read/write commands.
When 1, the address will be auto-incremented in multiple read/write commands.
bit 2-7: address AD(5:0). This is the address field of the indexed register.
bit 8-15: data DI(7:0) (write mode). This is the data that will be written into the device (MSb
first).
bit 8-15: data DO(7:0) (read mode). This is the data that will be read from the device (MSb
first).
In multiple read/write commands, further blocks of 8 clock periods will be added. When the
MS bit is ‘0’, the address used to read/write data remains the same for every block. When
the MS bit is ‘1’, the address used to read/write data is increased at every block.
The function and the behavior of SDI and SDO remain unchanged.
CS
SPC
SDI
SDO
RW
AD5 AD4 AD3 AD2 AD1 AD0
DI7DI6 DI5DI4 DI3DI2 DI1DI0
DO7DO6 DO5DO4 DO3DO2 DO1DO0
MS
相關PDF資料
PDF描述
LSN-0.75/16-D12HJ-C 1-OUTPUT 12.8 W DC-DC REG PWR SUPPLY MODULE
LSN-1.8/16-D12HJ-C 1-OUTPUT 28.8 W DC-DC REG PWR SUPPLY MODULE
LSN-1.2/16-D12HJ-C 1-OUTPUT 19.2 W DC-DC REG PWR SUPPLY MODULE
LSN-2.5/16-D12HJ-C 1-OUTPUT 40 W DC-DC REG PWR SUPPLY MODULE
LSN-1/16-D12HJ-C 1-OUTPUT 16 W DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
LSM330DLC 功能描述:加速計 - 板上安裝 iNEMO 3D SIP Module 2.4V to 3.6V IO 1.8V RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
LSM330DLCTR 功能描述:加速計 - 板上安裝 iNEMO 3D SIP Module 2.4V to 3.6V IO 1.8V RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
LSM330DLTR 功能描述:加速計 - 板上安裝 Linear Sensor Module 3D ACC 3D Gyro RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
LSM330DTR 制造商:STMicroelectronics 功能描述:INEMO INERTIAL MODULE: 3D ACCELEROMETER AND 3D GYROSCOPE
LSM330TR 功能描述:加速計 - 板上安裝 Inemo inertial module 3D accelerometer and 3D gyroscope RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*