- 您現在的位置：買賣IC網 > PDF目錄44922 > LS4501-9RD9B2 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE PDF資料下載
參數資料
| 型號： | LS4501-9RD9B2 |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| 封裝： | METAL, CASE S02, MODULE |
| 文件頁數： | 27/27頁 |
| 文件大小： | 599K |
| 代理商： | LS4501-9RD9B2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁
Cassette Style
100 Watt AC-DC Converters
S Series PFC
Edition 01/01.2001
9/27
Output Voltage Regulation of Double Output Modules
Output 1 is under normal conditions regulated to
Uo1 nom,
independent of the output currents.
Uo2 is dependent upon the load distribution. If both outputs
are loaded with more than 10% of
Io nom, the deviation of
Uo2 remains within
±5% of the value of U
o1. The following 3
gures show the regulation with varying load distribution. If
Io1 = Io2 or the two outputs are connected in series, the de-
viation of
Uo2 remains within
±1% of the value of U
o1 pro-
vided that a total load of more than 10% of
Io nom is applied.
Two outputs of a single S 5000 module connected in paral-
lel will behave like the output of a S 4000 module; the paral-
leled output is fully regulated. No precautions are neces-
sary in using the R-input and the test sockets.
Uo
Uo nom
0.98
0.5
0
0.5
1.0
Io1
IoL
Io
Io nom
05001
Fig. 9
Uo1 vs. Io1 (typ.) of single output units
Thermal Considerations
If a converter is located in free, quasi-stationary air (con-
vection cooling) at the indicated maximum ambient tem-
perature
TA max (see table: Temperature specifications) and
is operated at its nominal input voltage and output power,
the temperature measured at the
Measuring point of case
temperature TC (see: Mechanical Data) will approach the
indicated value
TC max after the warm-up phase. However,
the relationship between
TA and TC depends heavily on the
conditions of operation and integration into a system. The
thermal conditions are influenced by input voltage, output
current, airflow and temperature of surrounding compo-
nents and surfaces.
TA max is therefore, contrary to TC max,
an indicative value only.
Caution: The installer must ensure that under all operat-
ing conditions
TC remains within the limits stated in the
table:
Temperature specifications.
Notes: Sufficient forced cooling or an additional heat sink
allows
TA to be higher than 71
°C (e.g. 85°C) if T
C max is not
exceeded.
For -7 or -9 units at an ambient temperature
TA of 85
°C with
only convection cooling, the maximum permissible current
for each output is approx. 40% of its nominal value as per
figure.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
50
60
70
80
90
100
Io/Io nom
TA [°C]
0.9
1.0
Forced cooling
05089
TA min
TC max
Convection cooling
Fig. 8
Output current derating versus temperature for -7 and -9
units.
Thermal Protection
A temperature sensor generates an internal inhibit signal
which disables the outputs if the case temperature exceeds
TC max. The outputs are automatically re-enabled if the tem-
perature drops below this limit.
It is recommended that continuous operation under simul-
taneous extreme worst case conditions of the following
three parameters be avoided: Minimum input voltage,
maximum output power and maximum temperature.
Output Protection
Each output is protected against overvoltage which could
occur due to a failure of the control circuit by means of a
voltage suppressor diode which, under worst case condi-
tions, may become a short circuit. The suppressor diodes
are not designed to withstand externally applied over-
voltages. Overload at any of the two outputs will cause a
shut-down of both outputs. A red LED indicates the over-
load condition.
Parallel or Series Connection of Units
Single or double output units with equal nominal output volt-
age can be connected in parallel without any precautions
using option T.
With option T (current sharing), all units share the current
approximately equally.
Single output units and/or main and second outputs of dou-
ble output units can be connected in series with any other
(similar) output.
Note:
– Parallel connection of double output units should always
include both, main and second output to maintain good
regulation of both outputs.
– Not more than 5 units should be connected in parallel.
– Series connection of second outputs without involving
their main outputs should be avoided as regulation may
be poor.
– The maximum output current is limited by the output with
the lowest current limitation if several outputs are con-
nected in series.
Output Voltage Regulation of Single or Double Output
Modules with Outputs 1 and 2 Connected in Series
相關PDF資料 |
PDF描述 |
|---|---|
| LS4601-7EPD5TB2 | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LS4601-7EPT | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LS4601-7PD8B2 | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LS4601-7RD4B2 | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LS4601-7RD5TB2 | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LS4-53 | 制造商:Panduit Corp 功能描述: |
| LS4-54 | 制造商:Panduit Corp 功能描述: |
| LS-454/U | 制造商:undefined 功能描述: |
| LS454U | 制造商: 功能描述: 制造商:TELP 功能描述: 制造商:undefined 功能描述: |
| LS45-500 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。