- 您現在的位置：買賣IC網 > PDF目錄358934 > LPC47M14H-NC (SMSC Corporation) FIBER-SAFE KIT SCA-FS9500 PDF資料下載
參數資料
| 型號： | LPC47M14H-NC |
| 廠商： | SMSC Corporation |
| 英文描述： | FIBER-SAFE KIT SCA-FS9500 |
| 中文描述： | 128引腳ENGANCED超級I / O與LPC接口和USB集線器控制器 |
| 文件頁數： | 116/205頁 |
| 文件大?。?/td> | 1219K |
| 代理商： | LPC47M14H-NC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁當前第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁
SMSC DS – LPC47M14X
Page 116
Rev. 03/19/2001
6.16 PME SUPPORT
The LPC47M14x offers support for power management events (PMEs), also referred to as a System Control Interrupt
(SCI) events in an ACPI system. A power management event is indicated to the chipset via the assertion of the
nIO_PME signal. In the LPC47M14x, the nIO_PME is asserted by active transitions on the ring indicator inputs nRI1
and nRI2, valid NEC infrared remote control frames, active keyboard-data edges, active mouse-data edges,
programmable edges on GPIO pins and fan tachometer event. The GP42/nIO_PME pin, when selected for the
nIO_PME function, can be programmed to be active high or active low via the polarity bit in the GP42 register. The
output buffer type of the pin can be programmed to be open-drain or push-pull via bit 7 of the GP42 register. The
nIO_PME pin function defaults to active low, open-drain output.
The PME functionality is controlled by the PME status and enable registers in the runtime registers block, which is
located at the address programmed in configuration registers 0x60 and 0x61 in Logical Device A. The PME Enable
bit, PME_EN, globally controls PME Wake-up events. When PME_EN is inactive, the nIO_PME signal can not be
asserted. When PME_EN is asserted, any wake source whose individual PME Wake Enable register bit, is asserted
can cause nIO_PME to become asserted.
The PME Wake Status register indicates that an enabled wake source has occurred, and if the PME_EN bit is set,
asserted the nIO_PME signal. The PME Status bit is asserted by active transitions of PME Wake sources.
PME_Status will become asserted independent of the state of the global PME enable bit, PME_En.
The following pertains to the PME status bits for each event:
The output of the status bit for each event is combined with the corresponding enable bit to set the PME
status bit.
The status bit for any pending events must be cleared in order to clear the PME_STS bit.
For the GPIO events, the polarity of the edge used to set the status bit and generate a PME is controlled by the
polarity bit of the GPIO control register. For non-inverted polarity (default) the status bit is set on the low-to-high
edge. If the EETI function is selected for a GPIO then both a high-to-low and a low-to-high edge will set the
corresponding PME status bits. Status bits are cleared on a write of ‘1’.
The PME Wake registers also include status and enable bits for the fan tachometer input.
See the “Keyboard and Mouse PME Generation” section for information about using the keyboard and mouse signals
to generate a PME.
In the LPC47M14x the nIO_PME pin can be programmed to be an open drain, active low, driver. The LPC47M14x
nIO_PME pin is fully isolated from other external devices that might pull the nIO_PME signal low; i.e., the nIO_PME
signal is capable of being driven high externally by another active device or pullup even when the LPC47M14x VCC
is grounded, providing VTR power is active. The LPC47M14x nIO_PME driver sinks 6mA at .55V max (see section
4.2.1.1 DC Specifications, page 122, in the “PCI Local Bus Specification,” revision 2.1).
The PME registers are run-time registers as follows. These registers are located in system I/O space at an offset
from PME_BLK, the address programmed in Logical Device A at registers 0x60 and 0x61.
The following registers are for GPIO wakeup events:
PME Wake Status 2 (PME_STS2), PME Wake Enable 2 (PME_EN2)
PME Wake Status 3 (PME_STS3), PME Wake Enable 3 (PME_EN3)
PME Wake Status 4 (PME_STS4), PME Wake Enable 4 (PME_EN4)
PME Wake Status 5 (PME_STS5), PME Wake Enable 5 (PME_EN5)
See PME register description in the “Runtime Registers” Section.
相關PDF資料 |
PDF描述 |
|---|---|
| LPC47M14L-NC | EZ STIX CABLE INSTALLER STICKS |
| LPC47M14M-NC | CAT5 MULTI 1X9 VIDEO DISTRIBUTION AMP |
| LPC47M14Q-NC | HD VIEW RECEIVER 2 PORT DAISYCHAINABLE |
| LPC47M14V-NC | AT PRINTER SERIAL CBL DB9 FEMALE - DB25 MALE |
| LPC47M14R-NC | 128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC47M14I-NC | 制造商:SMSC 制造商全稱:SMSC 功能描述:128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
| LPC47M14J-NC | 制造商:SMSC 制造商全稱:SMSC 功能描述:128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
| LPC47M14K-NC | 制造商:SMSC 制造商全稱:SMSC 功能描述:128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
| LPC47M14L-NC | 制造商:SMSC 制造商全稱:SMSC 功能描述:128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
| LPC47M14M-NC | 制造商:SMSC 制造商全稱:SMSC 功能描述:128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
發布緊急采購，3分鐘左右您將得到回復。