參數資料
型號： LPC2362FBD100
廠商： NXP Semiconductors N.V.
元件分類： 數學處理器
英文描述： Single-chip 16-bit-32-bit MCU; up to 128 kB flash with ISP-IAP, Ethernet, USB 2.0 device-host-OTG, CAN, and 10-bit ADC-DAC
封裝： LPC2361FBD100<SOT407-1 (LQFP100)|<<http://www.nxp.com/packages/SOT407-1.html<1<Always Pb-free,;LPC2362FBD100<SOT407-1 (LQFP100)|<<http://www.nxp.com/packages/SOT407-1.htm
文件頁數： 13/64頁
文件大?。?/td> 475K
代理商： LPC2362FBD100
LPC2361_62
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 5 — 25 October 2011
13 of 64
NXP Semiconductors
LPC2361/62
Single-chip 16-bit/32-bit MCU
[3]
5 V tolerant pad providing digital I/O with TTL levels and hysteresis and analog output function. When configured as the DAC output,
digital section of the pad is disabled.
[4]
Open-drain 5 V tolerant digital I/O pad, compatible with I
2
C-bus 400 kHz specification. This pad requires an external pull-up to provide
output functionality. When power is switched off, this pin connected to the I
2
C-bus is floating and does not disturb the I
2
C lines.
Open-drain configuration applies to all functions on this pin.
[5]
Pad provides digital I/O and USB functions. It is designed in accordance with the
USB specification, revision 2.0
(Full-speed and
Low-speed mode only).
[6]
5 V tolerant pad with 5 ns glitch filter providing digital I/O functions with TTL levels and hysteresis.
[7]
This pin has no built-in pull-up and no built-in pull-down resistor.
[8]
This pin has a built-in pull-up resistor.
[9]
5 V tolerant pad with 20 ns glitch filter providing digital I/O function with TTL levels and hysteresis.
[10] Pad provides special analog functionality.
[11] When the main oscillator is not used, connect XTAL1 and XTAL2 as follows: XTAL1 can be left floating or can be grounded (grounding
is preferred to reduce susceptibility to noise). XTAL2 should be left floating.
[12] If the RTC is not used, these pins can be left floating.
[13] Pad provides special analog functionality.
[14] Pad provides special analog functionality.
[15] Pad provides special analog functionality.
[16] Pad provides special analog functionality.
[17] Pad provides special analog functionality.
7. Functional description
7.1 Architectural overview
The LPC2361/2362 microcontroller consists of an ARM7TDMI-S CPU with emulation
support, the ARM7 local bus for closely coupled, high-speed access to the majority of
on-chip memory, the AMBA AHB interfacing to high-speed on-chip peripherals, and the
AMBA APB for connection to other on-chip peripheral functions. The microcontroller
permanently configures the ARM7TDMI-S processor for little-endian byte order.
The LPC2362 implements two AHBs in order to allow the Ethernet block to operate
without interference caused by other system activity. The primary AHB, referred to as
AHB1, includes the VIC and GPDMA controller.
The second AHB, referred to as AHB2, includes only the Ethernet block and an
associated 16 kB SRAM. In addition, a bus bridge is provided that allows the secondary
AHB to be a bus master on AHB1, allowing expansion of Ethernet buffer space into
off-chip memory or unused space in memory residing on AHB1.
In summary, bus masters with access to AHB1 are the ARM7 itself, the GPDMA function,
and the Ethernet block (via the bus bridge from AHB2). Bus masters with access to AHB2
are the ARM7 and the Ethernet block.
AHB peripherals are allocated a 2 MB range of addresses at the very top of the 4 GB
ARM memory space. Each AHB peripheral is allocated a 16 kB address space within the
AHB address space. Lower speed peripheral functions are connected to the APB. The
AHB to APB bridge interfaces the APB to the AHB. APB peripherals are also allocated a
2 MB range of addresses, beginning at the 3.5 GB address point. Each APB peripheral is
allocated a 16 kB address space within the APB address space.
相關PDF資料
PDF描述
LPC2364FBD100 ARM7 with 128 kB flash, 34 kB SRAM, Ethernet, USB 2.0 Device, CAN, and 10-bit ADC
LPC2365FBD100 ARM7 with 256 kB flash, 58 kB SRAM, Ethernet and 10-bit ADC
LPC2366FBD100 ARM7 with 256 kB flash, 58 kB SRAM, Ethernet, USB 2.0 Device, CAN, and 10-bit ADC
LPC2367FBD100 ARM7 with 512 kB flash, 58 kB SRAM, Ethernet and 10-bit ADC
LPC2368FBD100 ARM7 with 512 kB flash, 58 kB SRAM, Ethernet, USB 2.0 Device, CAN, SD-MMC, and 10-bit ADC
相關代理商/技術參數
參數描述
LPC2362FBD100,551 功能描述:ARM微控制器 - MCU 128K FL/ ETH USB OTG CAN RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2364 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
LPC2364_10 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
LPC2364FB100 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
LPC2364FBD100 制造商:NXP Semiconductors 功能描述:MCU 32BIT ARM7 10/100 USB CAN 制造商:NXP Semiconductors 功能描述:MCU 32BIT ARM7, 10/100, USB, CAN 制造商:NXP Semiconductors 功能描述:IC, 32BIT MCU, ARM7, 72MHZ, LQFP-100; Controller Family/Series:(ARM7); Core Size:32bit; No. of I/O's:70; Supply Voltage Min:3V; Supply Voltage Max:3.6V; Digital IC Case Style:LQFP; No. of Pins:100; Program Memory Size:128KB ;RoHS Compliant: Yes 制造商:NXP Semiconductors 功能描述:Microcontroller,LPC2364FBD100 72 MHz
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*